Paper:
Basic Study on Laser Forming of Curved Surfaces with Simulation
Keisuke Kishida*, Toshihiko Nakamura*, Hideki Aoyama*,
Naohisa Matsushita**, and Akihiko Ushimaru**
*Department of System Design Engineering, Keio University, 3-14-1 Hiyoshi, Kohoku, Yokohama, Kanagawa 223-8522, Japan
**Fujitsu Limited, 4-1-1 Kamikodana, Nakahara-ku, Kawasaki 211-8588, Japan
- [1] M. Otsu and H. Miura, “Three-Dimensional Forming of Sheet Metal, J. of Japan Laser Processing Society,” Vol.10, No.3, pp. 238-242, 2003.
- [2] T. Ueda, K. Yamada, S. Oikawa, and A. Hosokawa, “Basic Study on Laser Forming,” J. of the Japan Society for Precision Engineering, Vol.67, No.2, pp. 300-305, 2001.
- [3] M. Saeki, A. Sakakibara, and K. Hosokawa, “Simulation of Laser Forming – 1st Report, Effect of Plate Thickness and Beam Diameter on Bending Direction –,” J. of the Japan Society for Precision Engineering, Vol.74, No.2, pp. 160-165, 2008.
- [4] Y. Namba and T. Katayama, “Three Dimensional Thermal Elasticplastic Analysis of Laser Forming Process,” J. of the Japan Society for Precision Engineering, Vol.65, No.9, pp. 1330-1334, 1999.
- [5] M. Osawa, T. Hatayama, T. Okubo, and Y. Uchiyama, “Fundamental Study on Micro-forming by Laser Beam,” Annual Report Research Institute for Technology No. 20 Tokyo Denki University, No.20, pp. 113-118, 2001.
- [6] M. Osawa, Y. Itoh, and H. Sato, “Plastic forming of micro parts by laser beam,” Annual Report Research Institute for Technology No. 23 Tokyo Denki University, No.23, pp. 95-100, 2004.
- [7] M. Osawa, H. Ichikawa, and H. Sato, “Plastic Deformation of Thin Metal Sheet by Laser Beam,” Annual Report Research Institute for Technology No. 25 Tokyo Denki University, No.25, pp. 95-100, 2006.
- [8] T. Miyazaki, M. Saito, T. Tokunaga, T. Misu, and S. Yoshioka, “Diode Laser Forming of Thin Metal Plate Using Pre-bending Effect,” J. of the Japan Society for Precision Engineering, Vol.68, No.5, pp. 700-704, 2002.
- [9] T. Misu, Y. Sano, T. Miyazaki, S. Yoshioka, T. Tokunaga, and Y. Tanaka, “Laser Bending of Thin Metal Plate : effect of Workpiece Size and Shape on Bending Occurred due to Buckling Mode,” J. of the Japan Society for Precision Engineering, Vol.71, No.12, pp. 1536-1540, 2005.
- [10] Y. Okamoto, Y. Uno, K. Ohta, T. Shibata, S. Kubota, and Y. Namba, “Study on Precision Laser Forming of Plastic with YAG Laser,” J. of the Japan Society for Precision Engineering, Vol.66, No.6, pp. 891-895, 2000.
- [11] Y. Uno, Y. Okamoto, T. Shibata, M. Ohkubo, “Study on Laser Forming of Plastic by YAG Laser : Effect of Specimen Thickness on Deformation Characteristics,” J. of the Japan Society for Precision Engineering, Vol.68, No.3, pp. 466-471, 2002.
- [12] K. Matsuo and K. Matsuoka, “Development of New System for Developing Curved Shell Plates of Ships,” J. of the Japan Society of Mechanical Engineers, Part C, Vol.76, No.771, pp. 2797-2802, 2010.
- [13] The Iron and Steel Institute of Japan, “Iron and Steel Handbook,” Maruzen, Third Edition, 1981.
- [14] Japan Society of Thermophysical Properties, “Thermophysical Properties Handbook,” Youkendo, 1990.
- [15] M. Hasegawa, “Stainless Steel Handbook,” Nihon Kougyo Shinbunshya, 1960.
This article is published under a Creative Commons Attribution-NoDerivatives 4.0 Internationa License.