JRM Vol.28 No.2 pp. 129-137
doi: 10.20965/jrm.2016.p0129


Rail Structure Supporting Mechanism Using Foamable Resin for Pillar Expansion, Anchoring, and Fixation

Rui Fukui*, Kenta Kawae**, Yuta Kato*, and Masayuki Nakao*

*Department of Mechanical Engineering, School of Engineering, The University of Tokyo
7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656, Japan

**Department of Human and Engineered Environmental Studies, School of Frontier Sciences, The University of Tokyo
5-1-5 Kashiwanoha, Kashiwa-shi, Chiba 277-8563, Japan

September 28, 2015
February 5, 2016
April 20, 2016
hazardous environment, resin foam, unmanned construction, rail structure, modular robots
Human workforce working at the Fukushima Daiichi Nuclear Power Plant face severe health and safety risks owing to the presence of radioactive obstacles and debris caused by the accident and the subsequent shutdown of the plant. Under such circumstances, various robots are deployed to undertake many tasks, however, it is not easy for robots to realize smooth locomotion and efficient operation because radioactive debris and architectural structures such as steps and doors tend to hinder their movement. In addition, installable sensors and actuators are restricted in such an environment. To overcome these difficulties, we propose an automated construction system with modularized rail structure for robot locomotion and operation. The structure is anchored to walls or floors and enables working robots to reach a specific destination. This paper describes the development of a rail structure supporting mechanism. The developed mechanism applies resin foam to three different components: the actuator, adhesive material, and structural material. To our knowledge, these multi-modal applications of resin foam are quite unique and novel. Basic experiments were conducted using the developed prototype. Experimental results verified the feasibility of pillar expansion, anchoring, and fixation motions, and they also revealed the impact of the components' properties on the performance of the supports.
Rail structure supporting mechanism

Rail structure supporting mechanism

Cite this article as:
R. Fukui, K. Kawae, Y. Kato, and M. Nakao, “Rail Structure Supporting Mechanism Using Foamable Resin for Pillar Expansion, Anchoring, and Fixation,” J. Robot. Mechatron., Vol.28 No.2, pp. 129-137, 2016.
Data files:
  1. [1] M. Rosen, “Robots to the rescue: DARPA's robotics challenge inspires new disaster-relief technology,” Science News, Vol.186, No.12, pp. 16-20, 2014.
  2. [2] K. Chayama, A. Fujioka, K. Kawashima, H. Yamamoto, Y. Nitta, C. Ueki, A. Yamashita, and H. Asama, “Technology of Unmanned Construction System in Japan,” J. of Robotics and Mechatronics, Vol.26, No.4, pp. 403-417, 2014.
  3. [3] T. Furuta, T. Yoshida, T. Nishimura, and H. Yamato, “Development of the Exploring Robot toward Future Indoor Surveillance Mission in the Fukushima Daiichi Nuclear Power Plant,” J. of the Robotics Society of Japan, Vol.32, No.2, pp. 92-97, 2014.
  4. [4] T. Uehara and N. Suganuma, “Change of Environment Leading to Development of the Quadruped Robot,” J. of the Robotics Society of Japan, Vol.32, No.2, pp. 139-140, 2014.
  5. [5] T. Trainer, “Development of Unmanned Systems after March 2011 Incident,” J. of the Robotics Society of Japan, Vol.32, No.2, pp. 133-136, 2014.
  6. [6] K. Nagatani, S. Kiribayashi, Y. Okada, K. Otake, K. Yoshida, S. Tadokoro, T. Nishimura, T. Yoshida, E. Koyanagi, M. Fukushima, and S. Kawatsuma, “Emergency Response to the Nuclear Accident at the Fukushima Daiichi Nuclear Power Plants using Mobile Rescue Robots,” J. of Field Robotics, Vol.30, No.1, pp. 44-63, 2013.
  7. [7] K. Kon, H. Igarashi, N. Sato, and T. Kamegawa, “Development of a Practical Mobile Robot Platform for NBC Disasters and Its Field Test,” Proc. of IEEE Int. Symp. on Safety, Security, and Rescue Robotics (SSRR), pp. 1-6, 2012.
  8. [8] R. Hodoshima, K. Ueda, H. Ishida, M. Guarnieri, E. F. Fukushima, and S. Hirose, “Telerobotic Control System to Enhance Rescue Operations for Arm-Equipped Tracked Vehicle HELIOS IX,” J. of Robotics and Mechatronics, Vol.26, No.1, pp. 17-33, 2013.
  9. [9] R. Fukui, Y. Kato, R. Takahashi, W. Wan, and M. Nakao, “Automated Construction System of Robot Locomotion and Operation Platform for Hazardous Environments – Basic System Design and Feasibility Study of Module Transferring and Connecting Motions,” J. of Field Robotics, 2016 (in press).
  10. [10] J. W. Romanishin, K. Gilpin, and D. Rus, “M-blocks: Momentum-driven, magnetic modular robots,” Proc. of IEEE/RSJ Int. Conf. on Intelligent Robots and Systems, pp. 4288-4295, 2013.
  11. [11] A. Bowyer, “Automated Construction using Co-operating Biomimetic Robots,” University of Bath Department of Mechanical Engineering Technical Report, November 2000.
  12. [12] A. A. Yusof, T. Kawamura, and H. Yamada, “Evaluation of Constructor robot telegrasping Force Perception Using Visual, Auditory and Force Feedback Integration,” J. of Robotics and Mechatronics, Vol.24, No.6, pp. 949-957, 2012.
  13. [13] H. Yamada, T. Kawamura, and K. Ootsubo, “Development of a Teleoperation System for a Constructor robot,” J. of Robotics and Mechatronics, Vol.26, No.1, pp. 110-111, 2014.
  14. [14] R. Guzman, R. Navarro, J. Ferre, and M. Moreno, “RESCUER: Development of a Modular Chemical, Biological, Radiological, and Nuclear Robot for Intervention, Sampling, and Situation Awareness,” J. of Field Robotics, 2016 (in press).
  15. [15] M. Hashimoto, C. Yokogawa, and T. Sadoyama, “Development and Control of a Face Robot Imitating Human Muscular Structures,” Proc. of IEEE/RSJ Int. Conf. on Intelligent Robots and Systems, pp. 1855-1860, 2006.
  16. [16] I. Kumagai, K. Kobayashi, S. Nozawa, Y. Kakiuchi, T. Yoshikai, K. Okada, and M. Inaba, “Development of a Full Body Multi-Axis Soft Tactile Sensor Suit for Life Sized Humanoid Robot and an Algorithm to Detect Contact States,” Proc. of IEEE-RAS Int. Conf. on Humanoid Robots, pp. 526-531, 2012.
  17. [17] L. Q. Tan, S. Q. Xie, I. C. Lin, and T. Lin, “Development of a multifingered Robotic Hand,” Proc. of IEEE Int. Conf. on Information and Automation, pp. 1541-1545, 2009.
  18. [18] W. Wang, S. Shams, D. Shin, C. Han, and H. Choi, “Soft Biomimetic Leg Design and Fabrication Process of Cockroach-Inspired Robot,” Proc. of IEEE Int. Conf. on Mechatronics and Automation, pp. 1405-1409, 2010.
  19. [19] J. G. Broughton and A. R. Hutchinson, “Adhesive systems for structural connections in timber,” Int. J. of Adhesion and Adhesives, Vol.21, No.3, pp. 177-186, 2001.
  20. [20] R. Fujisawa, N. Naohisa, S. Okazaki, R. Sato, Y. Ikemoto, and S. Dobata, “Active modification of the environment by a robot with construction abilities,” ROBOMECH J., Vol.2, No.9, 2015.
  21. [21] S. Revzen, M. Bhoite, A. Macasieb, and M. Yim, “Structure synthesis on-the-fly in a modular robot,” Proc. of IEEE/RSJ Int. Conf. on Intelligent Robots and Systems, pp. 4797-4802, 2011.

*This site is desgined based on HTML5 and CSS3 for modern browsers, e.g. Chrome, Firefox, Safari, Edge, Opera.

Last updated on Jul. 19, 2024