single-au.php

IJAT Vol.19 No.4 pp. 441-447
doi: 10.20965/ijat.2025.p0441
(2025)

Research Paper:

Wireless Microactuator Using Temperature-Sensitive Magnetic Material for Remote Operation

Kaiji Sato ORCID Icon

Department of Mechanical Engineering, Toyohashi University of Technology
1-1 Hibarigaoka, Tempaku-cho, Toyohashi, Aichi 441-8580, Japan

Corresponding author

Received:
February 3, 2025
Accepted:
April 29, 2025
Published:
July 5, 2025
Keywords:
wireless, microactuator, temperature-sensitive magnetic material, gripper, rotary micromechanism
Abstract

This paper presents a novel wireless microactuator that utilizes a temperature-sensitive magnetic material (TSMM) for remote operation. The microactuator consists of a TSMM part, permanent magnets, and a laser light source that heats a specific area of the TSMM part. The driving principle is based on a decrease in the saturation magnetic flux density of the TSMM with increasing temperature, which enables continuous force generation and movement. Two prototype mechanisms, namely a microgripper and a rotary micromechanism, were designed and fabricated to demonstrate the capabilities of the proposed actuator. The prototype microgripper was designed such that the finger carrying the microobject and the actuator environment were separated by a thin glass. The finger and the actuator were connected by magnetic coupling such that the microobject and the actuator could be used in their respective environments. The prototype of the rotary micromechanism was designed to consist of a small number of parts with simple shapes. Magnetic field analysis showed that the microgripper generated a gripping force of 2.7 mN, and the rotary micromechanism generated a torque of more than 50 µNm. The experimental results confirmed the continuous movement of the two prototype mechanisms under laser irradiation. The motions of the actuator and the magnetically coupled finger in the microgripper were measured, and the differences in motion were confirmed. The motion of the rotary micromechanism was measured under three different laser powers, and it was confirmed that the higher the power, the faster the TSMM ring rotated.

Cite this article as:
K. Sato, “Wireless Microactuator Using Temperature-Sensitive Magnetic Material for Remote Operation,” Int. J. Automation Technol., Vol.19 No.4, pp. 441-447, 2025.
Data files:
References
  1. [1] K. F. Ehmann, R. E. DeVor, and S. G. Kapoor, “Micro/meso-scale mechanical manufacturing: Opportunities and challenges,” The Proc. of the JSME Materials and Processing Conf., pp. 6-13, 2002. https://doi.org/10.1299/jsmeintmp.10.1.6
  2. [2] W. J. Polacheck and C. S. Chen, “Measuring cell-generated forces: A guide to the available tools,” Nature Methods, Vol.13, No.5, pp. 415-423, 2016. https://doi.org/10.1038/nmeth.3834
  3. [3] X. Liu and Y. Sun, “Microfabricated glass devices for rapid single cell immobilization in mouse zygote microinjection,” Biomedical Microdevices, Vol.11, No.6, pp. 1169-1174, 2009. https://doi.org/10.1007/s10544-009-9333-5
  4. [4] H. G. Le, N. L. Ho, and T.-P. Dao, “Design synthesis, modeling, control strategies, and fabrication methods of compliant grippers for micromanipulation and micromanipulator: A comprehensive review,” Robotics and Computer-Integrated Manufacturing, Vol.92, Article No.102893, 2025. https://doi.org/10.1016/j.rcim.2024.102893
  5. [5] J. Agnus, P. Nectoux, and N. Chaillet, “Overview of microgrippers and design of a micromanipulation station based on a MMOC microgripper,” 2005 Int. Symp. on Computational Intelligence in Robotics and Automation, pp. 117-123, 2005. https://doi.org/10.1109/CIRA.2005.1554264
  6. [6] Y. Tanaka, R. Suzuki, K. Edamura, and S. Yokota, “Design and fabrication of micro gripper using functional fluid power,” Int. J. Automation Technol., Vol.16, No.4, pp. 448-455, 2022. https://doi.org/10.20965/ijat.2022.p0448
  7. [7] M. Gao et al., “Two-dimensional materials for wireless power transfer,” Device, Vol.1, No.2, Article No.100022, 2023. https://doi.org/10.1016/j.device.2023.100022
  8. [8] A. Ichikawa et al., “On-chip enucleation of an oocyte by untethered microrobots,” J. of Micromechanics and Microengineering, Vol.24, No.9, Article No.095004, 2014. https://doi.org/10.1088/0960-1317/24/9/095004
  9. [9] L. Chen et al., “Wireless powered dielectric elastomer actuator,” IEEE Robotics and Automation Letters, Vol.6, No.4, pp. 7278-7284, 2021. https://doi.org/10.1109/LRA.2021.3097271
  10. [10] S. Ramya et al., “Thermal inplane microgripper for handling micro-objects,” 7th Int. Conf. on Communication and Electronics Systems, pp. 210-214, 2022. https://doi.org/10.1109/ICCES54183.2022.9835816
  11. [11] M. Akbari, F. Barazandeh, and H. Barati, “A novel approach to design and fabricate an electrothermal microgripper for cell manipulation,” Sensors and Actuators A: Physical, Vol.346, Article No.113877, 2022. https://doi.org/10.1016/j.sna.2022.113877
  12. [12] C. Elbuken, L. Gu, C. L. Ren, M. Yavuz, and M. B. Khamesee, “A monolithic polymeric microgripper with photo-thermal actuation for biomanipulation,” 2008 IEEE Int. Conf. on Mechatronics and Automation, pp. 707-711, 2008. https://doi.org/10.1109/ICMA.2008.4798843
  13. [13] Y. Okazaki, “Microfactories – A new methodology for sustainable manufacturing –,” Int. J. Automation Technol., Vol.4, No.2, pp. 82-87, 2010. https://doi.org/10.20965/ijat.2010.p0082
  14. [14] R. K. Jain, S. Saha, and S. Majumder, “Development of piezoelectric actuator based compliant micro gripper for robotic peg-in-hole assembly,” 2013 IEEE Int. Conf. on Robotics and Biomimetics, pp. 1562-1567, 2013. https://doi.org/10.1109/ROBIO.2013.6739689
  15. [15] D. O. Popa and H. E. Stephanou, “Micro and mesoscale robotic assembly,” J. of Manufacturing Processes, Vol.6, No.1, pp. 52-71, 2004. https://doi.org/10.1016/S1526-6125(04)70059-6
  16. [16] M. Ghafarian et al., “An XYZ micromanipulator for precise positioning applications,” J. of Micro-Bio Robotics, Vol.16, No.1, pp. 53-63, 2020. https://doi.org/10.1007/s12213-020-00124-5
  17. [17] J. J. Lee, Y. Dong, Y. H. Jeon, and M. G. Lee, “Design of a planar 3-DOF parallel micromanipulator,” J. of Mechanical Science and Technology, Vol.27, No.10, pp. 2985-2990, 2013. https://doi.org/10.1007/s12206-013-0814-3
  18. [18] S. Maruo and Y. Hiratsuka, “Optically driven micromanipulators with rotating arms,” J. Robot. Mechatron., Vol.19, No.5, pp. 565-568, 2007. https://doi.org/10.20965/jrm.2007.p0565
  19. [19] P. Polimeno et al., “Optical tweezers and their applications,” J. of Quantitative Spectroscopy and Radiative Transfer, Vol.218, pp. 131-150, 2018. https://doi.org/10.1016/j.jqsrt.2018.07.013
  20. [20] Y. Mizutani, Y. Otani, and N. Umeda, “Two-dimensional actuator using temperature sensitive ferrite by photo-thermal effect,” IEEJ Trans. on Sensors and Micromachines, Vol.126, No.4, pp. 170-171, 2006 (in Japanese). https://doi.org/10.1541/ieejsmas.126.170
  21. [21] Proterial Metals, Ltd. (in Japanese). https://www.metals.proterial.com/product/liv/08.html [Accessed January 13, 2025]
  22. [22] T. Hama and K. Sato, “Novel and compact thermomagnetic actuator using temperature-sensitive magnetic materials,” Int. J. of Precision Engineering and Manufacturing, Vol.18, No.12, pp. 1833-1840, 2017. https://doi.org/10.1007/s12541-017-0212-3

*This site is desgined based on HTML5 and CSS3 for modern browsers, e.g. Chrome, Firefox, Safari, Edge, Opera.

Last updated on Jul. 04, 2025