IJAT Vol.10 No.3 pp. 348-355
doi: 10.20965/ijat.2016.p0348


Temperature Variations in Drilling of CFRP/Aluminum and CFRP/Titanium Stacks

Masahiko Sato, Hisataka Tanaka, and Kanae Yamamoto

Department of Mechanical and Aerospace Engineering, Tottori University
4-101 Koyamacho-minami, Tottoti-shi, Tottori 680-8552, Japan

Corresponding author, E-mail:

October 1, 2015
March 9, 2016
May 2, 2016
CFRP--aluminum stack, CFRP--titanium stack, drilling, temperature
This paper describes the temperature variations observed in the drilling of carbon fiber-reinforced plastic (CFRP)/Al, CFRP/Ti, Al/CFRP, and Ti/CFRP stacks. An infrared radiation pyrometer equipped with an optical fiber was used to measure the temperature. The optical fiber, inserted into the oil hole of an internal-coolant carbide drill, registered the infrared rays radiating from the bottom surfaces of the drilled holes. In drilling the CFRP/Ti stack, the temperature was ∼95°C in the CFRP layer. As the drill progressed into the Ti layer, the temperature increased to a very high value of 745°C at the bore exit. In the Ti/CFRP stack, meanwhile, the initial temperature was ∼170°C and increased to 695°C at the Ti/CFRP interface. Severe thermal damage, including fiber/resin pullout and matrix degradation, was caused by the heat at the bottom surface of the drilled hole in the Ti/CFRP stack. Along the edge of the entry point in the CFRP, the CFRP matrix was degraded by the heat. In drilling the CFRP/Al stack, the temperature in the Al layer was 200°C; little thermal damage was observed.
Cite this article as:
M. Sato, H. Tanaka, and K. Yamamoto, “Temperature Variations in Drilling of CFRP/Aluminum and CFRP/Titanium Stacks,” Int. J. Automation Technol., Vol.10 No.3, pp. 348-355, 2016.
Data files:
  1. [1] D. Liu, Y. Tang and W. L. Cong, “A review of mechanical drilling for composite laminates,” Composite Structures, Vol.94, No.5, pp. 1265-1279, 2012.
  2. [2] A. M. Abrão, P. E. Faria, J. C. Campos Rubio, P. Reis, and J. Paulo Davim, “Drilling of fiber reinforced plastics: A review,” Journal of Materials Processing Technology, Vol.186, Nos.1-3, pp. 1-7, 2007.
  3. [3] E. Brinksmeier and R. Janssen, “Drilling of Multi-Layer Composite Materials consisting of Carbon Fiber Reinforced Plastics (CFRP), Titanium and Aluminum Alloys,” CIRP Annals – Manufacturing Technology, Vol.51, No.1, pp. 87-90, 2002.
  4. [4] I. Shyha, S. L. Soo, D. K. Aspinwall, S. Bradley, S. Dawson, and C. J. Pretorius, “Drilling of Titanium/CFRP/Aluminium Stacks,” Key Engineering Materials, Vol.447-448, pp. 624-633.
  5. [5] I. S. Shyha, S. L. Soo, D. K. Aspinwall, S. Bradley, R. Perry, P. Harden, and S. Dawson, “Hole quality assessment following drilling of metallic-composite stacks,” Int. Journal of Machine Tools and Manufacture, Vol.51, Nos.7-8, pp. 569-578, 2011.
  6. [6] D. Kim and M. Ramulu, “Drilling process optimization for graphite/bismaleimide-titanium alloy stacks,” Composite Structures, Vol.63, No.1, pp. 101-114, 2004.
  7. [7] M. Ramulu, T. Branson, and D. Kim, “A study on the drilling of composite and titanium stacks,” Composite Structures, Vol.54, No.1, pp. 67-77, 2001.
  8. [8] R. Li and A. J. Shih, “Tool Temperature in Titanium Drilling,” ASME Journal of Manufacturing Science and Engineering, Vol.129, No.4, pp. 740-749, 2007.
  9. [9] J. S. Agapiou and D. A. Stephenson, “Analytical and Experimental Studies of Drill Temperatures,” ASME Journal of Engineering for Industry, Vol.116 No.1, pp. 54-60, 1994.
  10. [10] S. Han, J. T. Lin, Y. Yamada, and D. D. L. Chung, “Enhancing the thermal conductivity and compressive modulus of carbon fiber polymer–matrix composites in the through-thickness direction by nanostructuring the interlaminar interface with carbon black,” Carbon, Vol.46, Issue 7, pp. 1060-1071, 2008.

*This site is desgined based on HTML5 and CSS3 for modern browsers, e.g. Chrome, Firefox, Safari, Edge, Opera.

Last updated on Jul. 19, 2024