Design of Wearable Power Assist Wear for Low Back Support Using Pneumatic Actuators
Xiangpan Li, Toshiro Noritsugu, Masahiro Takaiwa,
and Daisuke Sasaki
Graduate School of Natural Science and Technology, Okayama University, 3-1-1 Tsushimanaka, Kita-ku, Okayama 700-8530, Japan
This research focuses on developing a safe, lightweight, power assist device that can be worn by people during lifting or static holding tasks to prevent them from experiencing Low Back Pain (LBP). In consideration of their flexibility, light weight, and large force to weight ratio, two types of pneumatic actuators are employed in assisting low back movement for their safety and comfort. Actuator A is an elongation-type pneumatic rubber artificial muscle that is installed in the outer layer of the garment. Its two ends are fixed on the shoulders and thighs. It can output contractile force, assisting the erector spinae muscles in the same direction. Compared to McKibben-type pneumatic rubber artificial muscle, the elongation type has a larger contraction rate. Actuator B is a layer-type of pneumatic actuator; it is composed of two balloons, and it is installed in the inner layer of the garment. By taking into account the biomechanic structure of the human spine, this device can provide support in two ways. Actuator A acts as an external muscle power generators to reduce the force requirement for the erector spinae muscles. As actuator B acts as a moment arm of the contractile force generated by actuator A, it will increase the effective amount of torque. The device can be worn directly on the body like normal clothing. Because there is no rigid exoskeleton frame structure, it is lightweight and user friendly. The system’s Inertial Measurement Unit (IMU), composed of accelerometer sensors and gyro sensors to measure the human motion signals, can monitor the angles of the human body in real-time mode. By measuring the EMG signal of the human erector spinae muscles, the assistance effectiveness of the proposed device has been proven through experiments.
and Daisuke Sasaki, “Design of Wearable Power Assist Wear for Low Back Support Using Pneumatic Actuators,” Int. J. Automation Technol., Vol.7, No.2, pp. 228-236, 2013.
-  H. Kamioka and T. Honda, “Low Back Pain in Female Caregivers in Nursing Homes, Low Back Pain,” Ali Asghar Norasteh (Ed.), ISBN: 978-953-51-0599-2, InTech, 2012.
-  J. L. Pons, R. Ceres, and L. Calderón, “Introduction to Wearable Robotics, in Wearable Robots: Biomechatronic Exoskeletons,” J. L. Pons (Ed.), John Wiley & Sons, Ltd, Chichester, UK., 2008.
-  Y. Sankai, “HAL: Hybrid Assistive Limb Based on Cybernics,” Robotics Research, The 13th Int. Symp. ISRR, pp. 25-34, 2010.
-  M. Ishii, K. Yamamoto, and K. Hyodo, “Stand-Alone Wearable Power Assist Suit – Development and Availability –,” J. of Robotics and Mechatronics, Vol.17, No.5, pp. 575-583, 2005.
-  Y. Muramatsu, H. Kobayashi, Y. Sato, H. Jiaou, T. Hashimoto, and H. Kobayashi, “Quantitative Performance Analysis of Exoskeleton Augmenting Devices – Muscle Suit – for Manual Worker,” Int. J. of Automation Technology, Vol.5, No.4, pp. 559-567, 2011.
-  T. Kusaka, T. Tanaka, S. Kaneko, Y. Suzuki, M. Saito, and H. Kajiwara, “Assist Force Control of Smart Suit for Horse Trainers Considering Motion Synchronization,” Int. J. of Automation Technology, Vol.3, No.6, pp. 723-730, 2009.
-  K. Naruse, S. Kawai, H. Yokoi, and Y. Kakazu, “Design of Wearable Power-Assist Device for Lower Back Support,” J. of Robotics and Mechatronics, Vol.16, No.5, pp. 489-496, 2004.
-  M. Abdoli-E, J. M. Stevenson, S. A. Reid, and T. J. Bryant, “Mathematical and empirical proof of principle for an on-body personal lift augmentation device (PLAD),” J. of Biomechanics, Vol.40, pp. 1694-1700, 2007.
-  D. B. Chaffin, G. B. J. Andersson, and B. J. Martin, “Occupational Biomechanics,” 4th Ed., 2006.
-  M. Nordin, S. S. Weiner, “Biomechanics of the Lumbar Spine, Basic biomechanics of the musculoskeletal system,” Lippincott Williams & Wilkins, Third Ed., April 4, 2001.
-  J. Cholewicki, K. Juluru, A. Radebold, M. M. Panjabi, and S. M. McGill, “Lumbar spine stability can be augmented with an abdominal belt and/or increased intra-abdominal pressure,” European Spine J., Vol.8, No.5, pp. 388-395, 1999.
-  L. Gao, T. Noritsugu, M. Takaiwa, and D. Sasaki, “Development of Wearable Power Assist Device Using Curved Pneumatic rubber artificial Muscle,” Proc. of the 6th Int. Conf. on Fluid Power Transmission and Control ICFP 2005, pp. 330-334, 2005.
-  T. Noritsugu, D. Sasaki, M. Kameda, A. Fukunaga, and M. Takaiwa, “Wearable Power Assist Device for Standing Up Motion Using Pneumatic Rubber Artificial Muscles,” J. of Robotics and Mechatronics, Vol.19, No.6, pp.619-628, 2007.
-  T. Noritsugu, M. Takaiwa, and D. Sasaki, “Development of Power Assist Wear Using Pneumatic Rubber Artificial Muscles,” J. of Robotics and Mechatronics, Vol.21, No.5, pp. 607-613, 2009.
-  C.-P. Chou and B. Hannaford, “Static and dynamic characteristics of McKibben pneumatic artificial muscles,” Int. Conf. on Robotics and Automation, Vol.1, pp. 281-286, 1994.
-  G. K. Klute, J. M. Czerniecki, and B. Hannaford, “McKibben artificial muscles: pneumatic actuators with biomechanical intelligence,” IEEE/ASME int. conf. on advanced intelligent Mechatronics, Atlanta, GA, Sep. 19-22, 1999.
This article is published under a Creative Commons Attribution-NoDerivatives 4.0 Internationa License.