single-mostdl.php
IJAT Most Downloaded Papers, Dec. 2017
| This month | Last month | Vol. No. | Title / Authors | Keywords |
|---|---|---|---|---|
 |
- | Vol.9 No.5 (2015) |
Detection of Human Position and Motion by Thermopile Infrared Sensor Xipeng Zhang, Hiroaki Seki, and Masatoshi Hikizu |
thermopile infrared sensor, human position, body orientation, steepest descent method |
|
5 | Vol.11 No.1 (2017) |
“Industrie 4.0” and Smart Manufacturing – A Review of Research Issues and Application Examples Klaus-Dieter Thoben, Stefan Wiesner, and Thorsten Wuest |
industry 4.0, smart manufacturing, cyber-physical systems, industrial internet, smart factory |
 |
- | Vol.7 No.2 (2013) |
Laser-Generated Surface Acoustic Wave Technique for Crack Monitoring – A Review Kun Chen, Xing Fu, Dante J. Dorantes-Gonzalez, Yanning Li, Sen Wu, and Xiaotang Hu |
surface acoustic wave, laser-generated, crack monitoring, quantitative detection |
 |
1 | Vol.11 No.6 (2017) |
Precision Machining of Sintered Zirconia Ceramics by High-Speed Milling Yusuke Ito, Naohiko Sugita, Tatsuya Fujii, Toru Kizaki, and Mamoru Mitsuishi |
precision cutting, ceramics, zirconia, high-speed milling |
 |
5 | Vol.8 No.1 (2014) |
In-Process and On-Machine Measurement of Machining Accuracy for Process and Product Quality Management: A Review Yasuhiro Takaya |
in-process measurement, on-machine measurement, manufacturing metrology, machine tools, quality management |
|
- | Vol.3 No.3 (2009) |
Precision Positioning Control by Modeling Frictional Behaviors of Linear Ball Guideway Toshiharu Tanaka, Jiro Otsuka, and Takaaki Oiwa |
precision positioning, nonlinear frictional model, bristle model, linear ball guideway, circular contouring error |
 |
10 | Vol.9 No.3 (2015) |
An Exact Method for Robust Capacity Requirements Planning Daisuke Morita and Haruhiko Suwa |
capacity requirements planning, robust load plan, dynamic environment, uncertainty, exact method |
|
10 | Vol.9 No.2 (2015) |
FEM-Based Simulation for Workpiece Deformation in Thin-Wall Milling Jun Wang, Soichi Ibaraki, Atsushi Matsubara, Kosuke Shida, and Takayuki Yamada |
deformation, thin wall, milling, rib |
|
9 | Vol.7 No.2 (2013) |
Design of Wearable Power Assist Wear for Low Back Support Using Pneumatic Actuators Xiangpan Li, Toshiro Noritsugu, Masahiro Takaiwa, and Daisuke Sasaki |
power assist wear, low back, pneumatic rubber artificial muscle, IMU, iEMG |
|
- | Vol.8 No.2 (2014) |
Effect of Tool Run-Out on Micro-Groove Milling for a Microchannel Die Kenichi Iwatsuka, Yukio Maeda, Takanori Yazawa, and Shinya Suzuki |
cutting, milling, microchannel chip die, cutting force, tool run-out |
|
- | Vol.4 No.4 (2010) |
Redundant Parallel Mechanism for Haptic Applications Jumpei Arata and Hideo Fujimoto |
parallel mechanism, haptic device, redundancy |
|
- | Vol.5 No.6 (2011) |
Study of a Precision Pneumatic Positioning Device Using PZT Dither Yung-Tien Liu, Kuo-Ming Chang, and Huang-Ren Lee |
precision positioning, PZT dither, pneumatic actuator, Taguchi method, system identification |
|
9 | Vol.11 No.1 (2017) |
Cyber-Physical Product-Service Systems – Challenges for Requirements Engineering Stefan Wiesner, Eugenia Marilungo, and Klaus-Dieter Thoben |
cyber-physical systems, product-service systems, cyber-physical product-service systems, requirements engineering |
|
4 | Vol.10 No.2 (2016) |
Development of Cutting Force Prediction Method Using Motion Information from CNC Controller Tomoya Hida, Tetsuya Asano, Chiharu Higashino, Masaaki Kanamaru, Jun’ichi Kaneko, and Yoshimi Takeuchi |
cutting force, prediction, CNC, NC data, motion error |
Count period : December 1 - 31, 2017