In this paper, we propose a new fabrication method of high concentration carbon nanotube (CNT) composite phenolic resin bond for grinding tools and investigate the molding conditions by solvent casting method. CNT/diamond composite phenolic resin grinding tools with 12.5 vol% Ni-coated diamond grains and 20 vol% CNTs were prepared by the solvent casting method. The novolac phenolic resin with Hexamethylenetetramine as a hardener was used in this study. Partial curing of this resin occurs in the range of 40°C–90°C and harden completely at 180°C. The proposed solvent casting method involves two steps: desolvation and hot press for molding. Methanol or butanol was used as the solvent. When methanol solvent was used, desolvation was performed below 90°C before partial curing of phenol was completed. When butanol solvent was used, desolvation was performed at 100°C after partial curing of phenol. The effect of solvent and desolvation temperature on mechanical strength was determined from four-point bending tests. The porosity of the grinding tools was estimated by X-ray CT analysis, and the relationship between the porosity and mechanical strength was clarified. The effect of addition of CNTs on the phenolic curing process was also clarified by thermogravimetric-differential thermal analysis and Fourier-transform infrared spectroscopy. The mechanical strength of the grinding tools fabricated using methanol solvent and desolvated at room temperature and 40°C was approximately 70 MPa, and twice as high as that desolvated at 70°C. The mechanical strength of the grinding tools fabricated using butanol solvent and desolvated at 100°C was also 70 MPa. There was no difference in the dispersibility of diamond abrasive grains between the methanol and butanol samples; however, the porosity tended to be less in the butanol solvent. This study confirmed that the mechanical strength of CNT/diamond composite phenolic resin is affected by the amount and size of the voids. In particular, it was shown that better strength can be obtained by desolvation to avoid partial curing. The addition of CNTs may inhibit the curing reaction of phenol and hexamine owing to the glycidyl groups, which are functional groups of CNTs.

1. [1] T. Kawasato, H. Takamaru, K. Hamazono, M. Fukuta, K. Tanaka, Y. Chiba, M. Nagano, H. Kato, and Y. Kakinuma, “Slurry conditions for reaction-induced slurry-assisted grinding of optical glass lens,” Int. J. Automation Technol., Vol.17, No.1, pp. 40-46, 2023. https://doi.org/10.20965/ijat.2023.p0040
2. [2] T. Yamada, K. Ohashi, H. Suzuki, and A. Yui, “Special issue on high performance abrasive technologies,” Int. J. Automation Technol., Vol.16, No.1, pp. 3-4, 2022. https://doi.org/10.20965/ijat.2022.p0003
3. [3] S. Kashimura, K. Inazawa, H. Ohmori, and N. Itoh, “Development of resin fibrous grinding wheels using twin nozzle PELID and analysis of their grinding performance,” Int. J. Automation Technol., Vol.15, No.1, pp. 49-56, 2021. https://doi.org/10.20965/ijat.2021.p0049
4. [4] W. K. Chen, T. Kuriyagawa, H. Huang, and N. Yosihara, “Machining of micro aspherical mould inserts,” Precision Engineering, Vol.29, No.3, pp. 315-323, 2005. https://doi.org/10.1016/j.precisioneng.2004.11.002
5. [5] T. Kuriyagawa, K. Syoji, and L. Zhou, “Precision form truing and dressing for aspheric ceramics mirror grinding,” NIST Special Publication, Vol.847, pp. 325-331, 1993.
6. [6] T. Kuriyagawa, M. S. S. Zahmaty, and K. Syoji, “A new grinding method for aspheric ceramic mirrors,” J. of Materials Processing Technology, Vol.62, No.4, pp. 387-392, 1996. https://doi.org/10.1016/S0924-0136(96)02440-5
7. [7] T. Kuriyagawa, T. Shirosawa, O. Saitoh, and K. Syoji, “Development of micro ultrasonic abrasive machining system (1st report, studies in micro ultrasonic abrasive machining),” JSME Int. J., Series C: Mechanical Systems, Machine Elements and Manufacturing, Vol.45, No.2, pp. 593-600, 2002. https://doi.org/10.1299/jsmec.45.593
8. [8] T. Kuriyagawa, K. Syoji, and H. Ohshita, “Grinding temperature within contact arc between wheel and workpiece in high-efficiency grinding of ultrahard cutting tool materials,” J. of Materials Processing Technology, Vol.136, Nos.1-3, pp. 39-47, 2003. https://doi.org/10.1016/S0924-0136(02)00842-7
9. [9] H. Matsuura, Y. Kunieda, N. Yoshihara, J. Yan, and T. Kuriyagawa, “Development of 3R diamond wheel by thermoplastic resin bond,” Key Engineering Materials, Vol.329, pp. 459-464, 2007. https://doi.org/10.4028/www.scientific.net/KEM.329.459
10. [10] M. Ota, H. Suzuki, K. Ohashi, and T. Yamada, “Special issue on advanced abrasive processing technologies,” Int. J. Automation Technol., Vol.17, No.1, pp. 3-4, 2023. https://doi.org/10.20965/ijat.2023.p0003
11. [11] P. Kim, L. Shi, A. Majumdar, and P. L. McEuen, “Thermal transport measurements of individual multiwalled nanotubes,” Phys. Rev. Lett., Vol.87, Article No.215502, 2001. https://doi.org/10.1103/PhysRevLett.87.215502
12. [12] L. Shi, S. Plyasunov, A. Bachtold, P. L. McEuen, and A. Majumdar, “Scanning thermal microscopy of carbon nanotubes using batch-fabricated probes,” Appl. Phys. Lett., Vol.77, No.26, pp. 4295-4297, 2000. https://doi.org/10.1063/1.1334658
13. [13] S. Iijima, “Helical microtubules of graphitic carbon,” Nature, Vol.354, pp. 56-58, 1991. https://doi.org/10.1038/354056a0
14. [14] T. Suzuki, M. Kato, H. Saito, and H. Iizuka, “Effect of carbon nanotube (CNT) size on wear properties of Cu-based CNT composite electrodes in electrical discharge machining,” J. of Solid Mechanics and Materials Engineering, Vol.5, No.7, pp. 348-359, 2011. https://doi.org/10.1299/jmmp.5.348
15. [15] T. Suzuki and T. Konno, “Improvement in tool life of electroplated diamond tools by Ni-based carbon nanotube composite coatings,” Precision Engineering, Vol.38, No.3, pp. 659-665, 2014. https://doi.org/10.1016/j.precisioneng.2014.03.003
16. [16] N.-H. Tai, M.-K. Yeh, and J.-H. Liu, “Enhancement of the mechanical properties of carbon nanotube/phenolic composites using a carbon nanotube network as the reinforcement,” Carbon, Vol.42, Nos.12-13, pp. 2774-2777, 2004. https://doi.org/10.1016/j.carbon.2004.06.002
17. [17] M.-K. Yeh, N.-H. Tai, and J.-H. Liu, “Mechanical behavior of phenolic-based composites reinforced with multi-walled carbon nanotubes,” Carbon, Vol.44, No.1, pp. 1-9, 2006. https://doi.org/10.1016/j.carbon.2005.07.005
18. [18] M.-K. Yeh, N.-H. Tai, and Y.-J. Lin, “Mechanical properties of phenolic-based nanocomposites reinforced by multi-walled carbon nanotubes and carbon fibers,” Composites Part A: Applied Science and Manufacturing, Vol.39, No.4, pp. 677-684, 2008. https://doi.org/10.1016/j.compositesa.2007.07.010
19. [19] E. C. Botelho, M. L. Costa, E. R. Edwards, T. Burkhart, and B. Lauke, “Effects of carbon nanotube fillers dispersion on mechanical behavior of phenolic/carbon nanotube nanocomposite,” J. of Materials Research, Vol.27, No.18, pp. 2342-2351, 2012. https://doi.org/10.1557/jmr.2012.221
20. [20] R. B. Mathur, B. P. Singh, T. L. Dhami, Y. Kalra, N. Lal, R. Rao, and A. M. Rao, “Influence of carbon nanotube dispersion on the mechanical properties of phenolic resin composites,” Polymer Composites, Vol.31, No.2, pp. 321-327, 2010. https://doi.org/10.1002/pc.20807
21. [21] K. Sasaki, T. Suzuki, T. Fujii, and R. Ito, “Fabrication of well-dispersed carbon nanotube/phenolic resin composites for diamond grinding tools,” Proc. of the 23rd Int. Symp. on Advances in Abrasive Technology (ISAAT2021), pp. 217-222, 2021.
22. [22] H. Fujimoto, M. Abe, S. Osawa, O. Sato, and T. Takatsuji, “Development of dimensional X-ray computed tomography,” Int. J. Automation Technol., Vol.9, No.5, pp. 567-571, 2015. https://doi.org/10.20965/ijat.2015.p0567
23. [23] X. Peng and S. S. Wong, “Functional covalent chemistry of carbon nanotube surfaces,” Advanced Materials, Vol.21, No.6, pp. 625-642, 2009. https://doi.org/10.1002/adma.200801464
24. [24] T. Fujigaya and N. Nakashima, “Methodology for homogeneous dispersion of single-walled carbon nanotubes by physical modification,” Polymer J., Vol.40, pp. 577-589, 2008. https://doi.org/10.1295/polymj.PJ2008039
25. [25] T. Suzuki, M. Kato, H. Saito, and H. Iizuka, “Improved adherence strength between diamond grains and electrolytic nickel bonds by carbon nanotube coatings,” J. of Solid Mechanics and Materials Engineering. Vol.5, No.8, pp. 386-396, 2011. https://doi.org/10.1299/jmmp.5.386
26. [26] E. Takamitsu and M. Nishimura, “Curing reaction of phenolic novolac with hexamine,” J. of the Chemical Society of Japan, Vol.1973, No.11, pp. 2196-2201, 1973 (in Japanese). https://doi.org/10.1246/nikkashi.1973.2196
27. [27] M. Urabe, “The basics of infrared spectroscopy and its applications case,” Nippon Gomu Kyokaishi, Vol.90, No.12, pp. 571-576, 2017 (in Japanese). https://doi.org/10.2324/gomu.90.571