Top > IJAT > Energy Efficiency Improvement of Water Hydraulic Fluid Switchi ...

single-au.php

IJAT Vol.8 No.5 pp. 733-744
doi: 10.20965/ijat.2014.p0733
(2014)

Paper:

Views over last 60 days: 823

Energy Efficiency Improvement of Water Hydraulic Fluid Switching Transmission

Pha N. Pham*, Kazuhisa Ito*, and Shigeru Ikeo**

*Shibaura Institute of Technology, 307 Fukasaku, Minuma-ku, Saitama-city, Saitama 337-8570, Japan

**Sophia University, 7-1 Kioicho, Chiyoda-ku, Tokyo 102-8554, Japan

Received:
April 1, 2014
Accepted:
August 10, 2014
Published:
September 5, 2014
Creative Commons License
Keywords:
water hydraulics, energy efficiency, energy saving, velocity response, FST
Abstract
This study aims to determine effective methods for improving the energy efficiency of a water hydraulic Fluid Switching Transmission (FST). This paper introduces three methods to reduce energy consumption: lowering the velocity of the electric motor and stopping the motor during the working and deceleration phases, respectively (first method); restricting the working pressure within a certain range by using an unload valve (second method) or using the idling stop method (third method). Next these three methods are analyzed and compared. Experimental results show that by using the proposed methods, the energy and net energy consumption are greatly reduced. The greatest reductions are from 71.5 to 78.3% for energy consumption and from 65.1 to 66.2% for net energy consumption, corresponding to variations in the reference velocity from 600 to 1000 min-1. Additionally, the steady state errors in the proposed methods are slightly decreased in the working phase while the transient responses are almost the same for all cases.
Cite this article as:
P. Pham, K. Ito, and S. Ikeo, “Energy Efficiency Improvement of Water Hydraulic Fluid Switching Transmission,” Int. J. Automation Technol., Vol.8 No.5, pp. 733-744, 2014.
Data files:
References
  1. [1] P. N. Pham, K. Ito, and S. Ikeo, “Investigation on Velocity Response and Energy Saving Performance of Water Hydraulic Systems without Using Servo Valve,” Proc. of the 13th Scandinavian Int. Conf. on Fluid Power, SICFP 2013.
  2. [2] F. L. Yin, S. L. Nie, and J. Ruan, “Research on the Reliability of Sliding Bearing Support in a Swash.plate Type Axial Piston Water Hydraulic Pump,” Proc. of the 2011 Int. Conf. on Fluid Power and Mechatronics (FPM), 2011.
  3. [3] W. Kobayashi, K. Ito, and P. B. Zobel, “Development of Gaittraining Orthosis with Water Hydraulic Mackibben Muscles,” Proc. of the 7th SEATUC Symp., 2013.
  4. [4] F. Yoshida and S. Miyakawa, “Effect of Design Parameters on Response Characteristics of Water Hydraulic Proportional Control Valves,” Proc. of the 13th Scandinavian Int. Conf. on Fluid Power, SICFP 2013.
  5. [5] B. Hollingworth, “The Past, Present and Fu- ture of (Water) Hydraulics,” Proc. of the 12th Scandinavian Int. Conf. on Fluid Power, SICFP 2011.
  6. [6] F. Conrad, “Trends in Design of Water Hydraulics – Motion Control and Open-ended Solutions,” Proc. of the 6th JFPS Int. Symp. on Fluid Power, 2005.
  7. [7] J. M. García, G. W. Krutz, and L. J. John, “Self Propelled Water Hydraulic Vehicle,” Proc. of the 10th Scandinavian Int. Conf. on Fluid Power, SICFP 2007.
  8. [8] P. N. Pham, K. Ito, and S. Ikeo, “The Application of Simple Adaptive Control for Simulated Water Hydraulic Servo Motor System,” Proc. of the Int. Conf. on Industrial Technology, IEEE ICIT 2013.
  9. [9] Y. B. Ham, Y. B. Lee, and B. O. Choi, “A Study on the Application of Birfield Joint to aWater Hydraulic Piston Pump for Low Leakage and Low Friction Pumping,” Proc. of the the 6th JFPS Int. Symp. on Fluid Power, 2005.
  10. [10] Y. B. Ham, Y. B. Lee, and B. O. Choi, “Optimization of Floating Plate ofWater Hydraulic Internal Gear Pump,” Proc. of the 8th JFPS Int. Symp. on Fluid Power, 2011.
  11. [11] F. Majdič, J. Pezdirnik, and M. Kalin, “Comparative Tribological Investigations of Continuous Control Valves forWater Hydraulics,” Proc. of the 10th Scandinavian Int. Conf. on Fluid Power, SICFP 2007.
  12. [12] A. Mitsuhata, C. Liu, A. Kitagawa, and M. Kawashima, “Water Hydraulic Highspeed Solenoid Valve and Its Application,” Proc. of the 8th JFPS Int. Symp. on Fluid Power, 2011.
  13. [13] F. Conrad and F. Roli, “Mechatronics System Engineering for CAE/CAD, Motion Control and Design of Valve Actuators for Water Robot Applications,” Proc. of the 6th JFPS Int. Symp. on Fluid Power, 2005.
  14. [14] T. Kazama, “Numerical Simulation of a Slipper Model for Water Hydraulic Pumps/Motors in Mixed Lubrication,” Proc. of the 6th JFPS Int. Symp. on Fluid Power, 2005.
  15. [15] S. Oshima, T. Hirano, S. Miyakawa, and Y. Oobayashi, “Study on the Output Torque of a Water Hydraulic Planetary Gear Motor,” Proc. of the 12th Scandinavian Int. Conf. on Fluid Power, SICFP 2011.
  16. [16] D. Wu, Y. Liu, Z. Yang, H. Yang, and Z. Jiang, “Tribological Characteristics of Al2O3–3%TiO2/Al2O3 Under Silt–Laden Water Lubrication,” Proc. of the 12th Scandinavian Int. Conf. on Fluid Power, SICFP 2011.
  17. [17] Y. Yagi, H. A. Tasdemir, T. Tokoroyama, and N. Umehara, “The Development of Friction Tester in Pressurized HotWater at 30 MPa and 300°C,” Proc. of the 5th Int. Conf. on Manufacturing, Machine Design and Tribology, ICMDT 2013.
  18. [18] K. Ito,W. Kobayashi, P. N. Pham, and S. Ikeo, “Control and Energy Saving Performance of Water Hydraulic Fluid Switching Transmission,” Proc. of the 12th Scandinavian Int. Conf. on Fluid Power, SICFP 2011.
  19. [19] M. Linjama, “Digital Fluid Power State of the Art,” Proc. of the 12th Scandinavian Int. Conf. on Fluid Power, SICFP 2011.
  20. [20] R. Scheidl, H. Kogler, and B. Manhartsgruber, “A Cavitation Avoidance Strategy in Hydraulic Switching Control Based on a Nonlinear Oscillator,” Proc. of the 10th Scandinavian Int. Conf. on Fluid Power, SICFP 2007.
  21. [21] M. Linjama and M. Vilenius, “Digital Hydraulics Towards Perfect Valve Technology,” Proc. of the 10th Scandinavian Int. Conf. on Fluid Power, SICFP 2007.
  22. [22] P. Boström, M. Linjama, L. Morel, L. Siivonen, and M. Waldén, “Design and Validation of Digital Controllers for Hydraulic Systems,” Proc. of the 10th Scandinavian Int. Conf. on Fluid Power, SICFP 2007.
  23. [23] M. Karvonen, M. Heikkilä, M. Huova, M. Linjama, and K. Huhtala, “Simulation Study Improving Efficiency in Mobile Boom by Using Digital Hydraulic Power Management System,” Proc. of the 12th Scandinavian Int. Conf. on Fluid Power, SICFP 2011.
  24. [24] R. Inoguchi, K. Ito, and S. Ikeo, “Pure-Hydraulic Hybrid Cylinder Drive System with Hydraulic Transformer,” JFPS Int. J. of Fluid Power system, Vol.5, No.1, 2012.
  25. [25] K. Sanada, “Study on HILS of Fluid Switching Transmission,” Proc. of SICE–ICASE Int. Joint Conf., 2006.
  26. [26] P. N. Pham, K. Ito, W. Kobayashi, and S. Ikeo, “Research on Velocity Error and Energy Recovery Efficiency of Water Hydraulic Fluid Switching Transmission,” Proc. of the 11th Int. Conf. on Automation Technology, 2011.
  27. [27] P. N. Pham, K. Ito, W. Kobayashi, and S. Ikeo, “Analysis of Velocity Control Performance and Energy Recovery Efficiency ofWater Hydraulic Fluid Switching Transmission,” Int. J. of Automation Technology, Vol.6, No.4, pp. 457-467, 2012.
  28. [28] K. Ichiryu, “Experimental Investigation of Hybrid Vehicle,” Proc. of the 6th JFPS Int. Symp. on Fluid Power, 2005.
  29. [29] K. A. Stelson, “Saving the World’s EnergyWith Fluid Power,” Proc. of the 8th JFPS Int. Symp. on Fluid Power, 2011.
  30. [30] T. Wang and Q. Wang, “An Energy–Saving Pressure–Compensated Hydraulic System With Electrical Approach,” IEEE/ASME Trans. on Mechatronics, Vol.9, No.2, pp. 570-578, 2014.
  31. [31] M. Jelali and A. Kroll, “Hydraulic Servo–systems Modelling, Identification and Control,” Springer, 2014

Creative Commons License  This article is published under a Creative Commons Attribution-NoDerivatives 4.0 Internationa License.

*This site is desgined based on HTML5 and CSS3 for modern browsers, e.g. Chrome, Firefox, Safari, Edge, Opera.

Last updated on Apr. 18, 2024