Ultrasonic-Assisted Grinding of Ultra-High Purity SUS 316L

Keita Shimada; Nobuhito Yoshihara; Jiwang Yan; Tsunemoto Kuriyagawa; Yuichiro Sueishi; Hideshi Tezuka

doi:10.20965/ijat.2011.p0427

single-au.php

« previous

IJAT Vol.5 No.3 pp. 427-432

doi: 10.20965/ijat.2011.p0427

(2011)

Paper:

Views over last 60 days: 594

Ultrasonic-Assisted Grinding of Ultra-High Purity SUS 316L

Keita Shimada^*, Nobuhito Yoshihara^**, Jiwang Yan^,
Tsunemoto Kuriyagawa^, Yuichiro Sueishi^,
and Hideshi Tezuka^

^*Tohoku University, 6-6-01 Aoba, Aramaki-aza, Aoba-ku, Sendai, Miyagi 980-8579, Japan

^**Iwate University, 4-3-5 Ueda, Morioka, Iwate 020-8551, Japan

^***Tokyo Electric Power Company, 4-1 Egasaki-cho, Tsurumi-ku, Yokohama, Kanagawa 230-8510, Japan

Received:

January 28, 2011

Accepted:

February 27, 2011

Published:

May 5, 2011

Keywords:

ultrasonic-assisted grinding, ultra-high purity SUS316L, statistical model

Abstract

Ultra-High Purity (UHP) alloys providing such excellent properties as high corrosion resistance and toughness are difficult to machine efficiently due to these very properties. To improve machining efficiency, we applied ultrasonic-assisted micro-grinding to UHP alloy machining. We discuss the theoretical model we built of ultrasonic-assisted grinding to study grinding force using statistical calculation. We theoretically estimated and experimentally confirmed the effect of ultrasonic assistance on reducing grinding force.

Cite this article as:

K. Shimada, N. Yoshihara, J. Yan, T. Kuriyagawa, Y. Sueishi, and H. Tezuka, “Ultrasonic-Assisted Grinding of Ultra-High Purity SUS 316L,” Int. J. Automation Technol., Vol.5 No.3, pp. 427-432, 2011.

Data files:

References

[1] J. Kumabe, “Ultrasonic Grinding,” J. Jpn. Soc. Prec. Eng., Vol.27, No.6, pp. 369-371, 1961.
[2] M. Nomura, Y. Wu, M. Kato, andT. Kuriyagawa, “Effect of Ultrasonic Vibration in the Truing and Dressing of CBN Grinding Wheel used for Internal Grinding of Small Holes,” Key Engineering Materials, 291-292, 183-188, 2005.
[3] Y. Tanaka, H. Tsuwa, and A. Yano, “Study on the Fine Finishing by an Ultrasonically Vibrated Abrasive Stone (2^nd Report), On the Fine Finishing Resistance,” J. Jpn. Soc. Prec. Eng., Vol.30, No.3, pp. 253-258, 1964.
[4] K. Umino, K. Nishimura, A. Minagawa, and H. Tmomori, “The Trial Construction of Ultrasonic Grinding Equipment and the Machining Characteristics,” J. Jpn. Soc. Prec. Eng., Vol.52, No.1, pp. 107-113, 1986.
[5] S. Matsui and K. Shoji, “Statistical Approach to Grinding Mechanism, Undeformed Chip Length in Grinding,” J. Jpn. Soc. Prec. Eng., Vol.36, No.421, pp. 115-120, 1970.
[6] S. Matsui and K. Shoji, “Statistical Approach to Grinding Mechanism (2^nd Report), Grain Depth of Cut in Grinding,” J. Jpn. Soc. Prec. Eng., Vol.36, No.422, pp. 196-201, 1970.
[7] S. Matsui and K. Shoji, “Statistical Approach to Grinding Mechanism (3^rd Report), On a Few Experiments,” J. Jpn. Soc. Prec. Eng., Vol.36, No.422, pp. 196-201, 1971.

This article is published under a Creative Commons Attribution-NoDerivatives 4.0 Internationa License.

[1] [1] J. Kumabe, “Ultrasonic Grinding,” J. Jpn. Soc. Prec. Eng., Vol.27, No.6, pp. 369-371, 1961.

[2] [2] M. Nomura, Y. Wu, M. Kato, andT. Kuriyagawa, “Effect of Ultrasonic Vibration in the Truing and Dressing of CBN Grinding Wheel used for Internal Grinding of Small Holes,” Key Engineering Materials, 291-292, 183-188, 2005.

[3] [3] Y. Tanaka, H. Tsuwa, and A. Yano, “Study on the Fine Finishing by an Ultrasonically Vibrated Abrasive Stone (2^nd Report), On the Fine Finishing Resistance,” J. Jpn. Soc. Prec. Eng., Vol.30, No.3, pp. 253-258, 1964.

[4] [4] K. Umino, K. Nishimura, A. Minagawa, and H. Tmomori, “The Trial Construction of Ultrasonic Grinding Equipment and the Machining Characteristics,” J. Jpn. Soc. Prec. Eng., Vol.52, No.1, pp. 107-113, 1986.

[5] [5] S. Matsui and K. Shoji, “Statistical Approach to Grinding Mechanism, Undeformed Chip Length in Grinding,” J. Jpn. Soc. Prec. Eng., Vol.36, No.421, pp. 115-120, 1970.

[6] [6] S. Matsui and K. Shoji, “Statistical Approach to Grinding Mechanism (2^nd Report), Grain Depth of Cut in Grinding,” J. Jpn. Soc. Prec. Eng., Vol.36, No.422, pp. 196-201, 1970.

[7] [7] S. Matsui and K. Shoji, “Statistical Approach to Grinding Mechanism (3^rd Report), On a Few Experiments,” J. Jpn. Soc. Prec. Eng., Vol.36, No.422, pp. 196-201, 1971.

Ultrasonic-Assisted Grinding of Ultra-High Purity SUS 316L

Keita Shimada*, Nobuhito Yoshihara**, Jiwang Yan*, Tsunemoto Kuriyagawa*, Yuichiro Sueishi***, and Hideshi Tezuka***

Keita Shimada^*, Nobuhito Yoshihara^**, Jiwang Yan^,
Tsunemoto Kuriyagawa^, Yuichiro Sueishi^,
and Hideshi Tezuka^