Top > IJAT > Processing Micro Reactor by Non-Rotational Cutting Tool with U ...

single-au.php

IJAT Vol.3 No.5 pp. 602-609
doi: 10.20965/ijat.2009.p0602
(2009)

Paper:

Views over last 60 days: 341

Processing Micro Reactor by Non-Rotational Cutting Tool with Ultrasonic Vibration

Masafumi Yoshimaru, Hiroshi Koresawa, Hiroyuki Narahara,
and Hiroshi Suzuki

Kyusyu Institute of Technology, 680-4 Kawazu, Iizuka-shi, Fukuoka 820-8502, Japan

Received:
May 20, 2009
Accepted:
July 24, 2009
Published:
September 5, 2009
Creative Commons License
Keywords:
non-rotational cutting tool, ultrasonic vibration, micro reactor
Abstract
In recent years, a micro reactor used in the chemical field is capable of compounding reagents by the fine passage that intersects with in a complicated manner. The micro reactor is requested to have a high-quality finish because it uses not only a general acryl material, but also a hard vulnerable material such as a glass with excellent corrosion resistance. Etching technology is used as a method to provide a fine groove, but it requires tremendous amounts of money. This study attempts to manufacture the micro reactor using micro cutting by a non-rotational tool to process hard vulnerable materials. Processing in the ductile mode is indispensable for processing of a hard vulnerable material such as a glass. If this is realized, a good finish can be obtained. In this report, processing using ultrasonic vibration is performed as a means to implement processing in the ductile mode. We made a comparison with a finish by end mill tool and confirmed an increase in the infeed and the effect of cutting in water on the finish. We performed experiments on cutting the micro reactor under the optimum condition and confirmed that a non-rotational tool could process a hard vulnerable material. The following is a report of this matter.
Cite this article as:
M. Yoshimaru, H. Koresawa, H. Narahara, and H. Suzuki, “Processing Micro Reactor by Non-Rotational Cutting Tool with Ultrasonic Vibration,” Int. J. Automation Technol., Vol.3 No.5, pp. 602-609, 2009.
Data files:
References
  1. [1] T. Kumon, T. Ishida, Y. Takeuchi, T. Kawai, and K. Sawada, “Creation of Ultraprecision V-shaped Microgrooves Using Non- Rotational Cutting Tools,” Journal of the Japan Society for Precision Engineering, Vol.70, No.10, pp. 1301-1305, 2004.
  2. [2] M. Kouya, M. Shimada, H. Suzuki, H. Takeuchi, and M. Sato, “Development of CAM System for Non-rotating Machining of Curved Surface,” Journal of the Japan Society of Mechanical Engineers. Vol.62600, C, pp. 3326-3330, 1996.
  3. [3] H. Suzuki, “Mirror surface processing by six-axialed non-rotational cutting method,” Journal of the Japanese Society of Die and Mould Technology, Vol.16, No.8, pp. 22-23, 2001.
  4. [4] M. Yoshimaru, Y. Fujita, T. Ito, and H. Suzuki, “Application of the non-rotational cutting method to automatic seal groove processing,” Journal of the Japan Society for Precision Engineering, Vol.72, No.6, pp. 745-749, 2006.
  5. [5] M. Miyashita, “Ductile Mode Grinding Technology for Brittle Materials - The Way to Nanogrinding Technology,” Journal of the Japan Society for Precision Engineering, Vol.56, No.5, pp. 782-786, 1990.
  6. [6] S. Hagiwara, J. Murakami, T. Sano, and T. Obikawa, “Basic Research on the Evaluation of Tip Edge on Diamond Grain,” Journal of the Japan Society for Precision Engineering, Vol.71, No.5, pp. 618-622, 2005.
  7. [7] T. Ono and T. Matsumura, “Machining of Micro Channels on Glass with Square End Mill,” Journal of the Japan Society for Precision Engineering, Supplement Contribution, Vol.94, L03, pp. 1013-1014, 2004.
  8. [8] J. Kumabe, “Precision Processing with Vibration,” Jikkyo Shuppan Co., Ltd.
  9. [9] E. Shamoto, Y. C. Song, K. Sassa, H. Yoshida, R. Hino, and T. Moriwaki, “Proposal of Oblique Type of Elliptical Vibration Cutting and Its Basic Performance,” Journal of the Japan Society for Precision Engineering, Vol.69, No.7, pp. 970-975, 2003.
  10. [10] M. Yoshimaru, Y. Fujita, T. Ito, M. Kouya, and H. Suzuki, “Development of Multi-Axis Cutting Method Using Non-Rotational Tool with Ultrasonic Vibration,” Int. Journal of Automation Technology, Vol.2, No.2, pp. 105-109, 2008.
  11. [11] I. Ogura and Y. Okazaki, “Ductile-Regime Machining of Optical Glasses by Means of Single Point Diamond Turning,” Journal of the Japan Society for Precision Engineering, Vol.66, No.9, pp. 1431-1435, 2000.

Creative Commons License  This article is published under a Creative Commons Attribution-NoDerivatives 4.0 Internationa License.

*This site is desgined based on HTML5 and CSS3 for modern browsers, e.g. Chrome, Firefox, Safari, Edge, Opera.

Last updated on Oct. 01, 2024