Oil-air lubrication is commonly employed in rolling bearings for high-speed spindles in machining centers. However, grease-lubricated spindles which consume less lubricant and air have recently gained attention. This study evaluates the lubrication condition of a spindle based on its dynamic characteristics through contactless dynamic spindle testing. A grease-lubricated spindle, structurally identical to one previously studied under oil-air lubrication, was fabricated. Dynamic compliance was measured under various conditions, from which the eigenfrequencies and damping ratios were identified. The resulting viscous damping coefficients were compared to those of the oil-air-lubricated spindle. The results indicate that although the grease-lubricated spindle exhibits trends in modal parameters and viscous damping coefficients similar to those of the oil-air-lubricated spindle, the magnitudes of these variations differ considerably.

1. [1] H. Komiya, “Rolling bearing lubrication technology trends and R&D efforts,” JTEKT Eng. J. Engl. Ed., No.1003E, pp. 50-58, 2007.
2. [2] M. Aoki and S. Nakamura, “Technical trend and new technologies of the bearings for machine tool,” J. Jpn. Soc. Precis. Eng., Vol.74, No.9, pp. 913-916, 2008 (in Japanese). https://doi.org/10.2493/jjspe.74.913
3. [3] J. Li, “Lubricating grease: Experiments and modelling of wall-bounded and free-surface flows,” Ph.D. thesis, Luleå University of Technology, 2014.
4. [4] K. Jauhari, “Oil lubrication on high-speed spindle bearing system: A review,” Proc. Tribol. Ind., Vol.16, pp. 216-231, 2014.
5. [5] H. A. J. Sadiq Sha and P. P. Patil, “A review on lubrication systems with case study,” Seybold Rep., Vol.15, No.7, pp. 578-585, 2020.
6. [6] H. Cen and P. M. Lugt, “Replenishment of the EHL contacts in a grease lubricated ball bearing,” Tribol. Int., Vol.146, Article No.106064, 2020. https://doi.org/10.1016/j.triboint.2019.106064
7. [7] Y. H. Wijnant, J. A. Wensing, and G. C. Nijen, “The influence of lubrication on the dynamic behaviour of ball bearings,” J. Sound Vib., Vol.222, No.4, pp. 579-596, 1999. https://doi.org/10.1006/jsvi.1998.2068
8. [8] Y.-Y. Zhang, X.-L. Wang, and X.-L. Yan, “Dynamic behaviors of the elastohydrodynamic lubricated contact for rolling bearings,” J. Tribol., Vol.135, No.2, Article No.021501, 2013. https://doi.org/10.1115/1.4023084
9. [9] D. Dowson, G. R. Higginson, and A. V. Whitaker, “Elasto-hydrodynamic lubrication: A survey of isothermal solutions,” J. Mech. Eng. Sci., Vol.4, No.2, pp. 121-126, 1962. https://doi.org/10.1243/JMES_JOUR_1962_004_018_02
10. [10] W. Jacobs, R. Boonen, P. Sas, and D. Moens, “The influence of the lubricant film on the stiffness and damping characteristics of a deep groove ball bearing,” Mech. Syst. Signal Process., Vol.42, Nos.1-2, pp. 335-350, 2014. https://doi.org/10.1016/j.ymssp.2013.07.018
11. [11] I. Chowdhury, M. M. Sadek, and S. A. Tobias, “Determination of the dynamic characteristics of machine tool structures,” Proc. Inst. Mech. Eng., Vol.184, No.1, pp. 943-960, 1969. https://doi.org/10.1243/PIME_PROC_1969_184_069_02
12. [12] M. Rantatalo, J.-O. Aidanpää, B. Göransson, and P. Norman, “Milling machine spindle analysis using FEM and non-contact spindle excitation and response measurement,” Int. J. Mach. Tools Manuf., Vol.47, Nos.7-8, pp. 1034-1045, 2007. https://doi.org/10.1016/j.ijmachtools.2006.10.004
13. [13] X. Wang, Y. Guo, and T. Chen, “Measurement research of motorized spindle dynamic stiffness under high-speed rotating,” Shock Vib., Vol.2015, No.1, Article No.284126, 2015. https://doi.org/10.1155/2015/284126
14. [14] K. Iwai, S. Yamato, and A. Matsubara, “A simplified estimation of spindle dynamic compliance from current measurement for contactless electromagnetic excitation,” J. Manuf. Sci. Eng., Vol.147, No.1, Article No.011010, 2025. http://doi.org/10.1115/1.4067317
15. [15] Y. Matsuura, K. Yokohara, A. Matsubara, and S. Tsurutani, “Evaluation of dynamic characteristics of oil-air spindle using contact-less dynamic spindle tests—Effect of spindle installation and running conditions on dynamic compliance—,” J. Jpn. Soc. Precis. Eng., Vol.91, No.2, pp. 192-199, 2025 (in Japanese). https://doi.org/10.2493/jjspe.91.192
16. [16] J. Pemberton and A. Cameron, “A mechanism of fluid replenishment in elastohydrodynamic contacts,” Wear, Vol.37, No.1, pp. 185-190, 1976. https://doi.org/10.1016/0043-1648(76)90190-3
17. [17] E. Kingsbury, “Cross flow in a starved EHD contact,” ASLE Trans., Vol.16, No.4, pp. 276-280, 1973. https://doi.org/10.1080/05698197308982733
18. [18] R. Zeillinger and H. Köttritsch, “Damping in a rolling bearing arrangement,” Evolution, 1996. https://evolution.skf.com/damping-in-a-rolling-bearing-arrangement/ [Accessed August 5, 2025]
19. [19] P. Dietl, “Damping and stiffness characteristics of rolling element bearings: Theory and experiment,” Ph.D. thesis, Techischen Universität Wien, 1997. https://doi.org/10.13140/RG.2.2.18506.29122