Prediction of Built-Up Layer and Built-Up Edge Formation in Dry Cutting of SUS304 Stainless Steel
Xiaoqi Song, Yukio Takahashi, and Tohru Ihara
Department of Precision Mechanics, Chuo University
1-13-27 Kasuga, Bunkyo-ku, Tokyo 112-8551, Japan
This paper presents a thermodynamic model for studying the energy dissipation processes such as friction, wear, and the adhesion phenomenon in order to predict the built-up layer (BUL) and built-up edge (BUE) formation conditions in dry cutting of SUS304 stainless steel. The model is composed of three parts: the extended representative contact model (RCM) at the tool and chip interface, the thermodynamic analysis within the RCM, and the growth model. At a typical region, the RCM is characterized by three material elements and two boundary elements, which support the contact conditions between two material elements. Thermodynamic analysis within the RCM reveals that apart from friction and wear, the BUL/BUE formation is also an irreversible energy dissipation process. The BUL/BUE can be called as a “dissipative structure substance,” which can reduce tool wear. Meanwhile, the RCM is an open system because it allows for the transfer of energy and matter with its surrounding. Energy exchange and mass exchange exert significant influences on the BUL/BUE growth. It is verified that the BUL/BUE growth depends significantly on four energy dissipation processes: workpiece fracture, friction, workpiece accumulation, and reduction of adhesion. In addition, the proposed model is verified by comparing simulations with the corresponding experimental results of dry cutting of SUS304 stainless steel. It is verified that the BUL/BUE develops its characteristics with cutting time and that the proposed model can accurately predict the BUL/BUE formation conditions. These results have provided a deeper understanding of the BUL/BUE formation mechanisms.
-  T. H. C. Childs, “Ductile shear failure damage modelling and predicting built-up edge in steel machining,” J. Mater. Process. Technol., Vol.213, pp. 1954-1969, 2013.
-  H. Koichi and H. Tetsutaro, “On the Metal Cutting Mechanism with the Built-Up Edge,” Memoirs of the Faculty of Engineering, Hokkaido University, Vol.12, No.3, pp. 241-271, 1969.
-  N. Fang and P. Dewhurst, “Slip-line modeling of built-up edge formation inmachining,” Int. J. Mech. Sci., Vol.47, pp. 1079-1098, 2005.
-  E. Usui, K. Maekawa, and T. Shirakashi, “Simulation Analysis of Built-Up Edge Formation in Machining of Low Carbon Steel,” Bulletin of Jpn. Soc. Prec. Eng., Vol.15, pp. 237-242, 1981 (in Japanese).
-  E. Uhlmann, S. Henze, and K. Brommelhoff, “Influence of the built-up edge on the stress atate in the chip formation zone during orthogonal cutting of AISI1045,” Procedia CIRP, Vol.31, pp. 310-315, 2015.
-  S. N. B. Oliaei and Y. Karpat, “Investigating the influence of friction conditions on finite element simulation of microscale machining with the presence of built-up edge,” J. Adv. Manu. Tech., Vol.90, No.1, pp. 819-829, 2017.
-  X. Song, Y. He, W. M. Takahashi, and T. Ihara, “On the Formation Mechanisms of Adhering Layer during Machining Metal Material,” Key Eng. Mater., Vol.749, pp. 39-45, 2017.
-  X. Song, Y. Takahashi, W. He, and T. Ihara, “Study on usefulness of Built-up layer during machining of hardened steel,” J. Jpn. Soc. Prec. Eng., Vol.82, No.9, pp. 814-820, 2016 (in Japanese).
-  X. Song, Y. Takahashi, W. He, and T. Ihara, “Investigation on the nucleus formation mechanisms of Built-up layer in cutting of hardened steel,” J. Jpn. Soc. Prec. Eng., Vol.83, No.5, pp. 445-452, 2017 (in Japanese).
-  X. Song, Y. Takahashi, and T. Ihara, “Influence of Built-up layer on the wear of uncoated cemented carbide tool during cutting of Inconel 718,” LEM21 Proc., Vol.56, pp. 1-6, 2017.
-  A. Gomez-Parra, M. Alvarez-Alcon, J. Salguero, M. Batista, and M. Marcos, “Analysis of the Evolution of the Built-Up Edge and Built-Up Layer Formation Mechanisms in the Dry Turning of Aeronautical Aluminium Alloys,” Wear, Vol.302, pp. 1209-1218, 2013.
-  N. Tomac, K. Tonnessen, F. O. Rasch, and T. Mikac, “A study of factors that affect the built-up material formation,” AMST, CISM Courses and Lectures, Vol.486, pp. 183-192, 2005.
-  J. E. Desaigues, C. Lescalier, A. Bomont-Arzur, D. Dudzinski, and O. Bomont, “Experimental study of built-up layer formation during machining of high strength free-cutting steel,” J. Mat. Pro. Tech., Vol.236, pp. 204-215, 2016.
-  H. S. Qi and B. Mills, “Formation of a transfer layer at the tool-chip interface during machining,” Wear, Vol.245, pp. 136-147, 2000.
-  H. Kiyota, F. Itoigawa, S. Rndo, and T. Nakamura, “Analytical Approach for Optimization of Chamfered Cutting Tool Preparation Considering Built-Up Edge Extrusion Behavior,” Int. J. Automation Technol., Vol.7, No.3, pp. 329-336, 2013.
-  M. Kaladhar, K. V. Ubbalah, and C. H. S. Rao, “Machining of Austenitic stainless steels – a review,” Int. J. of Machining and Machinability of Materials, Vol.12, Nos.1-2, pp. 178-192, 2012.
-  T. Obikawa, Y. Asano, and Y. Kamata, “Computer fluid dynamics analysis for efficient spraying of oil mist in finish-turning of Inconel 718,” Int. J. Mach. Tools Manu., Vol.49, pp. 971-978, 2009.
-  T. Ihara, “Usefulness of adhesion/BUE during cutting,” Science of machine, Vol.66, No.10, pp. 825-832, 2014 (in Japanese).
-  L. Prigogine and D. Kondepudi, “Thermodynamique: Des moteurs thermiques aux structures dissipatives,” Éditions Odile Jacob, 1999 (in French).
-  Z. Palmai, “Proposal for a new theoretical model of the cutting tool’s flank wear,” Wear, Vol.303, pp. 437-445, 2013.
-  Z. Marzak, O. O. Mohand, and K. Aziz, “Modeling and simulation of the damage viscoplastic behavior of steel AISI 304,” Nature and Technology, Vol.15, pp. 37-44, 2016.
-  H. Keyvan and E. Ng, “A Combined Empirical and Numerical Approach for Tool Wear Prediction in Machining,” Procedia CIRP, Vol.31, pp. 304-309, 2015.
-  H. B. He, H. Y. Li, J. Yang, X. Y. Zhang, Q. B. Yue, X. Jiang, and S. Lyu, “A study on major factors influencing dry cutting temperature of AISI 304 stainless steel,” Int. J. Pre. Eng. Manu., Vol.18, No.10, pp. 1387-1392, 2017.
This article is published under a Creative Commons Attribution-NoDerivatives 4.0 International License.