Model-Based Installation of Viscoelastic Damper Support for Reduction of Residual Vibration
Kotaro Mori*,**,, Daisuke Kono*, Iwao Yamaji*, and Atsushi Matsubara*
Kyotodaigaku-Katsura, Nishikyo-ku, Kyoto 615-8540, Japan
**Japan Society for the Promotion of Science, Tokyo, Japan
It is necessary to increase the damping of a machine support structure (support damping) to reduce the residual vibrations caused by rocking vibration. The stiffness of the machine support system (support stiffness) is also an important parameter that needs to be considered while designing machine tools, to avoid low frequency vibrations. However, conventional passive damper supports decrease the support stiffness while increasing the damping. In our previous study, a passive viscoelastic non-linear damper system for shear vibrations, where the vertical preload determines its damping coefficient, was developed to increase the support damping without decreasing the stiffness by focusing on the horizontal component of rocking vibration. The magnitude dependency of the damping capacity has been modeled. However, this damper system has a tradeoff relationship between natural frequency and damping capacity caused by changes in the preload distribution. Thus, adjustment of the vertical preload applied on the damper is essential for the model-based installation of this damper system. So far, no method has been proposed considering this issue. The vertical preload has been adjusted by trial and error methods. This study proposes a method to determine the damper preload conditions systematically by considering the tradeoff relationship between natural frequency and damping capacity caused by changes in the preload distribution. This method is described based on the case study of a machining center. First, the relationship between preload distribution and support stiffness is investigated using the support stiffness model. Then, the relationship between damping capacity and vertical preloads on the damper is investigated based on material test results. Based on these investigations, the tradeoff relationships are simulated on a machining center by utilizing the damper model. The simulation results are verified with the experimental results. The results show that the proposed method can estimate the tradeoff relationship between natural frequency and damping capacity caused by the changes in the preload distribution. By utilizing this estimated relationship, the preferred preload condition can be decided depending upon the user’s demand.
-  F. Koenigsberger and J. Tlusty, “Machine Tool Structures,” 1st ed., Elsevier, 1970.
-  R. Sato, G. Tashiro, and K. Shirase, “Analysis of the Coupled Vibration Between Feed Drive Systems and Machine Tool Structure,” Int. J. Automation Technol., Vol.9, No.6, pp. 689-697, 2015.
-  D. B. DeBra, “Vibration isolation of precision machine tools and instruments,” Annals of the CIRP, Vol.41, pp. 711-718, 1992.
-  L. Zuo, “Element and System Design for Active and Passive Vibration Isolation,” Ph.D. thesis, Massachusetts Institute of Technology, 2004.
-  C. E. Okwudire and J. Lee, “Minimization of the residual vibrations of ultra-precision manufacturing machines via optimal placement of vibration isolators,” Precis. Eng., Vol.37, pp. 425-432, 2013.
-  C. F. J. Geerts and G. H. Veldhuizent, “Precision copying machine for variable curvature surfaces,” Precis. Eng., Vol.6, pp. 9-11, 1984.
-  J. Lee and C. E. Okwudire, “Reduction of vibrations of passively-isolated ultra-precision manufacturing machines using mode coupling,” Precis. Eng., Vol.43, pp. 164-177, 2016.
-  M. Law, M. Wabner, A. Colditz, M. Kolouch, S. Noack, and S. Ihlenfeldt, “Active vibration isolation of machine tools using an electro-hydraulic actuator,” CIRP J. of Manuf. Sci. Technol., Vol.10, pp. 36-48, 2015.
-  B. Denkena, M. Eckl, and T. Lepper, “Advanced Control Strategies for Active Vibration Suppression in Laser Cutting Machines,” Int. J. Automation Technol., Vol.9, No.4, pp. 425-435, 2015.
-  T. Kato, K. Kawashima, T. Funaki, K. Tadano, and T. Kagawa, “A new, high precision, quick response pressure regulator for active control of pneumatic vibration isolation tables,” Precis. Eng., Vol.34, pp. 43-48, 2010.
-  F. Matichard, B. Lantz, K. Mason, R. Mittleman, B. Abbott, E. Allwine et al, “Advanced LIGO two-stage twelve-axis vibration isolation and positioning platform. Part 2: Experimental investigation and tests results,” Precis. Eng., Vol.40, pp. 287-297, 2015.
-  F. Matichard, B. Lantz, K. Mason, R. Mittleman, B. Abbott, E. Allwine et al, “Advanced LIGO two-stage twelve-axis vibration isolation and positioning platform. Part 1: Design and production overview,” Precis. Eng., Vol.40, pp. 273-286, 2015.
-  Y. Shirahama, R. Sato, Y. Takasuka, H. Nakatsuji, and K. Shirase, “Machine Bed Support with sliding Surface for Improving the Motion Accuracy,” Int. J. Automation Technol., Vol.10, No.3, pp. 447-454, 2016.
-  K. Mori, D. Kono, I. Yamaji, and A. Matsubara, “Vibration reduction of machine tool using viscoelastic damper support,” Procedia CIRP, Vol.46, pp. 448-451, 2016.
-  K. Mori, D. Kono, I. Yamaji, and A. Matsubara, “Modelling of viscoelastic damper support for reduction in low frequency residual,” Precis. Eng., Vol.50, pp. 313-319, 2017.
-  H. Nakabayashi, “Properties and Applications of Polyisobutylene-based Thermo Plastic Elastomer,” Nippon Gomu Kyokaishi, Vol.83, No.9, pp. 284-288, 2010 (in Japanese).
-  D. Kono, S. Nishio, I. Yamaji, and A. Matsubara, “A method for stiffness tuning of machine tool supports considering contact stiffness,” Int. J. of Mach. Tools Manuf., Vol.90, pp. 50-59, 2015.
-  K. Mori, D. Kono, I. Yamaji, and A. Matsubara, “Support Placement for Machine Tools Using Stiffness Model,” Int. J. Automation Technol.,” Vol.9, No.6, pp. 680-688, 2015.
-  M. Kaneko and Y. Nakamura, “Mechanical modelling of visco-elastic damper with amplitude- and frequency-dependent properties,” J. of Struct. Eng. B, Vol.44, pp. 263-270, 1998 (in Japanese).
-  “Rubber, vulcanized or thermoplastic – Determination of dynamic properties – Part 1: General guidance,” ISO 4664-1, 2011.
This article is published under a Creative Commons Attribution-NoDerivatives 4.0 International License.