A Five-Axis Machining Error Simulator for Rotary-Axis Geometric Errors Using Commercial Machining Simulation Software
Soichi Ibaraki*,† and Ibuki Yoshida**
*Department of Mechanical Systems Engineering, Hiroshima University
1-3-2 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8511, Japan
**Department of Micro Engineering, Kyoto University
Katsura, Nishigyo-ku, Kyoto 616-8540, Japan
This paper presents a simulator that graphically presents the influence of rotary-axis geometric errors on the geometry of a finished workpiece. Commercial machining simulation software is employed for application to arbitrary five-axis tool paths. A five-axis kinematic model is implemented with the simulator to calculate the influence of rotary-axis geometric errors. The machining error simulation is demonstrated for 1) the cone frustum machining test described in ISO 10791-7:2015 , and 2) the pyramid-shaped machining test proposed by some of the authors in . The influences of the possible geometric errors are simulated in advance. By comparing the measured geometry of the finished workpiece to the simulated profiles, major error causes are identified without numerical fitting to the machine’s kinematic model.
-  ISO 10791-7:2015, Test conditions for machining centres – Part 7: Accuracy of a finished test piece.
-  S. Ibaraki and Y. Ota, “A machining test to calibrate rotary axis error motions of five-axis machine tools and its application to thermal deformation test,” Int. J. of Machine Tools and Manufacture, Vol.86, pp. 81-88, 2014.
-  J. Mayr, J. Jedrzejewski, E. Uhlmann, A. Donmez, W. Knapp, F. Härtig, K. Wendt, T. Moriwaki, P. Shore, R. Schmitt, C. Brecher, T. Würz, and K. Wegener, “Thermal issues in machine tools,” CIRP Annals – Manufacturing Technology, Vol.61, No.2, pp. 771-791, 2012.
-  M. Weck, P. McKeown, R. Bonse, and U. Herbst, “Reduction and Compensation of Thermal Errors in Machine Tools,” CIRP Annals – Manufacturing Technology, Vol.44, No.2, pp. 589-598, 1995.
-  J. Bryan, “International Status of Thermal Error Research,” Annals of the CIRP, Vol.39, No.2, pp. 645-656, 1990.
-  H. Schwenke, W. Knapp, H. Haitjema, A. Weckenmann, R. Schmitt, and F. Delbressine, “Geometric error measurement and compensation of machines – An update,” Annals of CIRP – Manufacturing Technology, Vol.57, No.2, pp. 560-575, 2008.
-  S. Ibaraki and W. Knapp, “Indirect Measurement of Volumetric Accuracy for Three-axis and Five-axis Machine Tools: A Review,” Int. J. of Automation Technology, Vol.6, No.2, pp. 110-124, 2012.
-  S. Ibaraki, Y. Nagai, H. Otsubo, Y. Sakai, S. Morimoto, and Y. Miyazaki, “R-Test Analysis Software for Error Calibration of Five-Axis Machine Tools – Application to a Five-Axis Machine Tool with Two Rotary Axes on the Tool Side –,” Int. J. of Automation Technology, Vol.9, No.4. pp. 387-395, 2015.
-  S. Ibaraki and Y. Ota, “Error Calibration for Five-Axis Machine Tools by On-the-Machine Measurement Using a Touch-Trigger Probe,” Int. J. of Automation Technology, Vol.8, No.1, pp. 20-27, 2014.
-  D. N. Reshetov and V. T. Portman, “Accuracy of Machine Tools,” ASME Press, New York, NY, USA, 1988.
-  I. Inasaki, K. Kishinami, S. Sakamoto, N. Sugimura, Y. Takeuchi, and F. Tanaka, “Shaper generation theory of machine tools – its basis and applications,” Yokendo, Tokyo, 1997 (in Japanese).
-  M. S. Uddin, S. Ibaraki, A. Matsubara, and T. Matsushita, “Prediction and compensation of machining geometric errors of five-axis machining centers with kinematic errors,” Precision Engineering, Vol.33, No.2, pp. 194-201, 2009.
-  C. Hong, S. Ibaraki, and A. Matsubara, “Influence of position-dependent geometric errors of rotary axes on a machining test of cone frustum by five-axis machine tools,” Precision Engineering, Vol.35, No.1, pp. 1-11, 2011.
-  S. Bossoni, “Geometric and Dynamic Evaluation and Optimization of Machining Centers,” Ph.D. dissertation, ETH Zurich, 2009.
-  V. Alessandro, C. Gianni, and S. Antonio, “Axis geometrical errors analysis through a performance test to evaluate kinematic error in a five axis tilting-rotary table machine tool,” Precision Engineering, Vol.39, pp. 224-233, 2015.
-  W. Wang, Z. Jiang, Q. Li, and W. Tao, “A new test part to identify performance of five-axis machine tool – Part II validation of S part,” Int. J. of Advanced Manufacturing Technology, Vol.79, pp. 739-756, 2015.
-  R. Sato, Y. Yokobori, and M. Tsutsumi, “Dynamic synchronous accuracy of translational axes and rotational axes in 5-axis machining center,” J. of the Japan Society for Precision Engineering, Vol.72, No.1, pp. 73-78, 2006 (in Japanese).
-  R. Sato, Y. Sato, K. Shirase, G. Campatelli, and A. Scippa, “Finished Surface Simulation Method to Predicting the Effects of Machine Tool Motion Errors,” Int. J. of Automation Technology, Vol.8, No.6, pp. 801-809, 2014.
-  H. Hasebe, W. Wakaoka, and T. Yamamoto, “An NC data analyzer for improving the quality of machined surface,” Proc. of the Mechanical Engineering Congress, pp. 329-330, 2004 (in Japanese).
-  H. Iwabe, K. Shimizu, and M. Sasaki, “Analysis of cutting mechanism by ball end mill using 3D-CAD,” JSME Int. J. Series C, Vol.49, No.1, pp. 28-34, 2006.
-  A. Scippa, N. Grossi, adn G. Campatelli, “Milled Surface Generation Model for Chip Thickness Detection in Peripheral Milling,” Procedia CIRP (14th CIRP Conference on Modeling of Machining Operations), Vol.8. pp. 450-455, 2013.
-  Y. Abbaszaheh-Mir, J. R. R. Mayer, G. Clotier, and C. Fortin, “Theory and simulation for the identification of the link geometric errors for a five-axis machine tool using a telescoping magnetic ball-bar,” Int. J. of Production Research, Vol.40, No.18, pp.4781-4797, 2002.
-  ISO 230-1:2012, Test code for machine tools – Part 1: Geometric accuracy of machines operating under no-load or quasi-static conditions.
-  ISO 230-7:2006, Test code for machine tools – Part 7: Geometric accuracy of axes of rotation.
-  VERICUT by CG Tech: http://www.cgtech.com/ [Accessed February 10, 2017]
-  NAS 979:1969, Uniform cutting test – NAS series, metal cutting equipment specifications; 34-37.
This article is published under a Creative Commons Attribution-NoDerivatives 4.0 International License.