High-precision positioning can be obtained by reducing sliding friction and securing support rigidity. A prototype of a biaxial positioning table with non-contact drive by magnetic force and flexible mechanism support was developed to meet these requirements. The magnetic poles of a permanent magnet and an electromagnet were placed opposite to each other with an appropriate gap between them, and the attraction force between the two poles was used as the actuator for fine feed. The table was supported with a flexible mechanism composed of metal (A2017) beams with notches and elastic hinges assembled into a square frame shape. The permanent magnets were commercial neodymium magnets, and the electromagnets were self-made of S45C core bars. Two types of attraction force, maximum and minimum, were set depending on the number of neodymium magnets and the magnetic pole gap. The relationship between the applied current and attraction force for each type was calibrated using an electronic balance. Upon increasing and decreasing the applied current to the electromagnets, a linear relationship was shown between them. The relationship between the attraction force and the X- and Y-axes displacements was simulated by finite element analysis. Based on both results, the relationship between the applied current and displacement was estimated. The fine-feed experiment was conducted in both directions of the X- and Y-axes by applying current to electromagnets in a stepwise sequence. The displacements of total strokes in the long-stroke feed on applying the maximum attraction force were 340 μm and 315 μm for the X-axis and 160 μm and 133 μm for the Y-axis. These values are 2.0–2.8 times larger than the estimated displacement. Additionally, 3%–12% of the other axes interference occurred between the X- and Y-axes. In the high resolution feed applying the minimum attraction force, the displacement per step was 75 nm and 78 nm for the X-axis and 35 nm and 39 nm for the Y-axis. Cooperative feed with a combination of long stroke and high resolution was verified to be feasible.

1. [1] A. A. M. Faudzi, Y. Sabzehmeidani, and K. Suzumori, “Application of Micro-Electro-Mechanical Systems (MEMS) as Sensors: A Review,” J. Robot. Mechatron., Vol.32, No.2, pp. 281-288, doi: 10.20965/jrm.2020.p0281, 2020.
2. [2] K. Sato, “Trend of Precision Positioning Technology,” ABCM Symp. Ser. Mechatron., Vol.2, pp. 739-750, 2006.
3. [3] R. Sato, “Sensor-less Estimation of Positioning Reversal Value for Ball Screw Feed Drives,” Precis. Eng., Vol.60, pp. 116-120, doi: 10.1016/j.precisioneng.2019.06.011, 2019.
4. [4] Y. Tamaru, H. Shimizu, and H. Kamoda, “Correction of Positioning and Angular Errors for Ball Screw Feed Unit,” Trans. of the JSME, Vol.80, No.816, DR0240, doi: 10.1299/transjsme.2014dr0240, 2014 (in Japanese).
5. [5] K. Sato, “Practical and Intuitive Controllers for Precision Motion: AR-CM NCTF Control of Ball Screw Mechanism,” Int. J. Automation Technol., Vol.5, No.6, pp. 793-799, doi: 10.20965/ijat.2011.p0793, 2011.
6. [6] A. Oyanguren, J. Larrañaga, and I. Ulacia, “Thermo-mechanical Modelling of Ball Screw Preload Force Variation in Different Working Conditions,” Int. J. Adv. Manuf. Technol., Vol.97, pp. 723-739, doi.: 10.1007/s00170-018-2008-8, 2018.
7. [7] T. Nozaki and J. Otsuka, “Reduction of Thermal Deformation in a Motor Precision Positioning Device Cooled by Peltier Elements,” Int. J. Automation Technol., Vol.7, No.5, pp. 544-549, doi: 10.20965/ijat.2013.p0544, 2013.
8. [8] N. Zhu, S. Koshimizu, T. Nozaki, K. Taneishi, J. Otsuka, T. Shirai, T. Nishide, and T. Togashi, “Decrease of Thermal Expansion of Ball Screw Used for Precision Positioning Devices by Peltier Module Cooling Based on Feedback Method,” Int. J. Automation Technol., Vol.7, No.5, pp. 564-570, doi: 10.20965/ijat.2013.p0564, 2013.
9. [9] T. Tanaka, J. Otsuka, I. Masuda, Y. Aoyama, and A. Inagaki, “Sub-Nanometer Resolution Positioning Device Driven by New Type of Linear Motor with Linear Ball Guideways – Considering Time Lag of Electric Control System –,” Int. J. Automation Technol., Vol.5, No.6, pp. 832-841, doi: 10.20965/ijat.2011.p0832, 2011.
10. [10] Y. Sakai, T. Tanaka, H. Yoshioka, J. Zhu, M. Tsutsumi, and Y. Saito, “Influence of Nonlinear Spring Behavior of Friction on Dynamic Characteristics of a Rolling Guideway,” J. Advanced Mechanical Design, Systems, and Manufacturing, Vol.9, No.1, JAMDSM0004, doi: 10.1299/jamdsm.2015jamdsm0004, 2015.
11. [11] T. Shigematsu, M. K. Kurosawa, and K. Asai, “Nanometer stepping drives of surface acoustic wave motor,” IEEE Trans. on Ultrasonics, Ferroelectrics, and Frequency Control, Vol.50, No.4, pp. 376-385, doi: 10.1109/TUFFC.2003.1197960, 2003.
12. [12] Y. Irie, S. Hirata, C. Kanamori, and H. Aoyama, “Impact Piezo-Driven Micro Dispenser and Precise Miniature XY Stage,” J. Robot. Mechatron., Vol.27, No.3, pp. 259-266, doi: 10.20965/jrm.2015.p0259, 2015.
13. [13] Y. Tamaru and K. Takafuji, “Cooperated Positioning Control for Ultraprecision Positioning in Extended Stroke Path (Applied to Continuous Step Positioning),” Trans. of the JSME: Series C, Vol.77, No.777, pp. 2139-2145, doi: 10.1299/kikaic.77.2139, 2011 (in Japanese).
14. [14] H. Isobe and A. Kyusojin, “Non-Contact Guideway for Substrate Transportation by Ultrasonic Oscillation,” Int. J. Automation Technol., Vol.2, No.3, pp. 199-204, doi: 10.20965/ijat.2008.p0199, 2008.
15. [15] T. Ide, J. Friend, K. Nakamura, and S. Ueha, “A Low-Profile Design for the Noncontact Ultrasonically Levitated Stage,” Japanese J. Applied Physics, Vol.44, No.6C, pp. 4662-4665, 2005.
16. [16] T. Ide, J. Friend, K. Nakamura, and S. Ueha, “A Non-contact Linear Bearing and Actuator via Ultrasonic Levitation,” Sensors and Actuators A: Physical, Vol.135, No.2, pp. 740-747, doi: 10.1016/j.sna.2006.08.005, 2007.
17. [17] Y. Tamaru and H. Shimizu, “Linear Slider Supported by Squeezed air Films with Self-Propulsion Mechanism Based on Floating Height Difference,” Trans. of the JSME, Vol.83, No.854, 17-00278, doi: 10.1299/transjsme.17-00278, 2017 (in Japanese).
18. [18] T. Oiwa and M. Katsuki, “Survey of Questionnaire on Ultra-precision Positioning,” J. of JSPE, Vol.86, No.10, pp. 735-740, doi: 10.2493/jjspe.86.735, 2020 (in Japanese).
19. [19] M. Cirolini, A. F. Flores Filho, Y. C. Wu, and D. G. Dorrell, “Design Aspects of a Reluctance-Based Magnetic Lead Screw,” IEEE Trans. on Magnetics, Vol.55, Vol.7, pp. 1-6, doi: 10.1109/TMAG.2019.2895681, 2019.
20. [20] T. Shinshi, J. Hashimoto, B. Chen, K. Sato, and A. Shimokohbe, “A New Magnetic Lead Screw and Its Basic Characteristics,” Trans. of the JSME: Series C, Vol.64, No.618, pp. 690-697, doi: 10.1299/kikaic.64.690, 1998 (in Japanese).
21. [21] M. Takahashi, “Design Concept and Structural Configuration of Magnetic Levitation Stage with Z-Assist System,” Int. J. Automation Technol., Vol.15, No.5, pp. 706-714, doi: 10.20965/ijat.2021.p0706, 2021.