Paper:
Data Assimilation Mechanism for Lifecycle Simulation Focusing on Process Behaviors
Kazuho Fujimoto, Shinichi Fukushige, and Hideki Kobayashi
Department of Mechanical Engineering, Graduate School of Engineering, Osaka University
2-1 Yamadaoka, Suita, Osaka 565-0871, Japan
Corresponding author
Systematic lifecycle design and management are promising approaches for constructing sustainable product lifecycle systems. Lifecycle simulation (LCS) has been used to evaluate a product lifecycle in the design phase from both the environmental and economic perspectives. Based on material flows through each process of the product lifecycle, the LCS calculates the time variation in environmental loads, cost, and profit. In each process of the LCS model, functions that regulate the behaviors of the process, called behavior functions, are set, and these functions control material flows. Previously, we proposed a data-assimilated LCS method that combines data assimilation (DA) with LCS to realize adaptive management based on actual states of the product lifecycle. In this previous development, the DA mechanism modified the material flows of an entire lifecycle in the simulation model based on actual flows observed in each process at the time of the DA. However, because process behaviors were not modified, the gap between material flows predicted by the simulation and the flows of the actual lifecycle increased over time. To overcome this limitation, in this study, we propose a new DA mechanism that modifies the behaviors of un-observed processes based on observed material flows. The proposed DA mechanism uses the response surface methodology to estimate the behaviors while tracing the causal relation in the LCS model in reverse. A case study on a photovoltaic panel reuse business showed that the DA mechanism successfully merged the observed data into the process behaviors in the LCS model including the processes where no data were observed, thereby improving the accuracy of the simulation for future prediction. Systematically analyzing the current and future process states of the product lifecycle can support decision-making in lifecycle management.
- [1] P. Ghisellini, C. Cialani, and S. Ulgiati, “A review on circular economy: the expected transition to a balanced interplay of environmental and economic systems,” J. of Cleaner Production, Vol.114, pp. 11-32, 2016.
- [2] E. McKinsey & Company, “Towards the circular economy; Accelerating the scale-up across global supply chains,” World Economic Forum, 2013.
- [3] Y. Umea, S. Takata, F. Kimura, T. Tomiyama, J. W. Sutherland, S. Kara, C. Herrmann, and J. R. Duflou, “Toward integrated product and process life cycle planning – An environmental perspective,” CIRP Annals, Vol.61, pp. 681-702, 2012.
- [4] G. Sonnemann and M. Margni, “Life Cycle Management: LCA Compendium – the Complete World of Life Cycle Assessment,” Springer Nature, 2015.
- [5] H. Kobayashi, “Strategic evolution of eco-products: a product life cycle planning methodology,” Research in Engineering Design, Vol.16, pp. 1-16, 2005.
- [6] E. Kunii, T. Matsumura, S. Fukushige, and Y. Umeda, “Proposal of Consistency Management Method Between Product and its Life Cycle for Supporting Life Cycle Design,” Int. J. Automation Technol., Vol.6, No.3, pp. 272-278, 2012.
- [7] Y. Umeda, S. Fukushige, E. Kunii, and Y. Matsuyama, “LC-CAD: A CAD system for life cycle design,” CIRP Annals, Vol.61, pp. 175-178, 2012.
- [8] Y. Umeda, A. Nonomura, and T. Tomiyama, “Study on life-cycle design for the post mass production paradigm,” Artificial Intelligence for Engineering Design, Analysis and Manufacturing, Vol.14, Issue 2, pp. 149-161, 2000.
- [9] T. Kumazawa and H. Kobayashi, “A simulation system to support the establishment of circulated business,” Advanced Engineering Informatics, Vol.20, Issue 2, pp. 127-136, 2006.
- [10] H. Murata, N. Yokono, S. Fukushige, and H. Kobayashi, “A Lifecycle Simulation Method for Global Reuse,” Int. J. Automation Technol., Vol.12, No.6, pp. 814-821, 2018.
- [11] F. Kimura and H. Suzuki, “Product Life Cycle Modelling for Inverse Manufacturing,” Proc. of the IFIP WG5.3 Int. Conf. on Life-Cycle Modelling for Innovative Products and Processes, pp. 80-89, 1996.
- [12] F. Kimura, “A Methodology for Design and Management of Product Life Cycle Adapted to Product Usage Modes,” Proc. of the CIRP Int. Seminar on Manufacturing Systems, pp. 139-142, 2000.
- [13] S. Fukushige, M. Nishioka, and H. Kobayashi, “Data-assimilated life cycle simulation for adaptive product lifecycle management,” CIRP Annals, Vol.66, Issue 1, pp. 37-40, 2017.
- [14] D. P. Dee, S. M. Uppala, A. J. Simmons, P. Berrisford, P. Poli, S. Kobayashi, U. Andrae, M. A. Balmaseda, G. Balsamo, P. Bauer, P. Bechtold, A. C. M. Beljaars, L. van de Berg, J. Bidlot, N. Bormann, C. Delsol, R. Dragani, M. Fuentes, A. J. Geer, L. Haimberger, S. B. Healy, H. Hersbach, E. V. Hólm, L. Isaksen, P. Kållberg, M. Köhler, M. Matricardi, A. P. McNally, B. M. Monge-Sanz, J. J. Morcrette, B. K. Park, C. Peubey, P. de Rosnay, C. Tavolato, J. N. Thépaut, and F. Vitart, “The ERA-Interim reanalysis: configuration and performance of the data assimilation system,” Quarterly J. of the Royal Meteorological Society, Vol.137, Issue 656, pp. 553-597, 2011.
- [15] C. Irrgang, J. Saynisch, and M. Thomas, “Utilizing oceanic electromagnetic induction to constrain an ocean general circulation model: A data assimilation twin experiment,” J. of Advances in Modeling Earth Systems, Vol.9, Issue 3, pp. 1703-1720, 2017.
- [16] X. Xie, V. Alexander, and G. Feng, “Data Assimilation in Discrete Event Simulation – a Rollback based Sequential Monte Carlo Approach,” 2016 Symp. on Theory of Modeling and Simulation (TMS-DEVS), No.11, pp. 1-8, 2016.
- [17] R. H. Myers, D. C. Montgomery, and C. M. Anderson-Cook, “Response surface methodology: Process and product optimization using designed experiments – 3rd Edition,” John Wiley & Sons, Inc., 2009.
- [18] S. Yamada, “Design of experiments – Method edition, from basic theory to response surface method, Taguchi method, and optimal programming,” JUSE Press, 2004 (in Japanese).
- [19] “JPEA PV OUTLOOK 2030,” Japan Photovoltaic Energy Association (JPEA). http://www.jpea.gr.jp/pdf/pvoutlook2015-1.pdf [Accessed January 21, 2020].
- [20] Y. Matsuyama, S. Fukushige, and Y. Umeda, “A Modeling Method for a Product Life Cycle Focusing on Representation of Individual Products,” J. of the Japan Society for Precision Engineering, Vol.82, No.1, pp. 106-114, 2016.
This article is published under a Creative Commons Attribution-NoDerivatives 4.0 Internationa License.