Scheduling Algorithm Using Path Relinking for Production Process with Crane Interference
Research on the Positioning and Recognition of an Intelligent Inspection Robot in Substations
Development of High-Speed Rotation Polishing System with Slurry Confinement and Friction-State Control
Finishing Speed Improvement Using Side Cover Plates in Gyro Finishing
Slurry Conditions for Reaction-Induced Slurry-Assisted Grinding of Optical Glass Lens
Effects of Bit Shape of Electroplated Diamond Tool Used for Drilling Small Diameter Holes in Glass Plate on Machining Fluid Flow and Chip Discharge
Evaluation of Dressing Condition Based on Quantification of Grinding Wheel Surface Conditions
Three-Dimensional Evaluation of Microscopic Wheel Surface Topography in Creep Feed Grinding Using Ceramics Grinding Wheel
Influence of the Impact Angle on Machining in Powder Jet Processing
Special Issue on Advanced Abrasive Processing Technologies
Power Consumption Simulation of Servo Motors Focusing on the Influence of Mechanical Vibration on Motor Efficiency
Effect of Grain Size on Change in Surface Roughness of Carbon Steels Through Polishing Processes
Rotary Cutting with Ultrasonic Vibration of Hardened Steel
Surface Texturing Technique Based on Ultrasonic Turning for Improving Tribological Properties
Development of Ultrasonic Vibration-Assisted Magnetic Compound Fluid (MCF) Polishing Technology
Polishing Performance of a Recycled Grinding Wheel Using Grinding Wheel Scraps for the Wet Polishing of Stainless-Steel Sheets
Polishing Characteristics and Mechanism of Polishing Glass Substrate Using Suede Pad with Fine Micrometer-Sized Pores
Effect of Types of Grinding Fluid on Grinding Characteristics of CMSX4
Effect of the Abrasive Grain Distribution on Ground Surface Roughness
Optimization of Nano-Topography Distribution by Compensation Grinding
ELID Mirror Surface Grinding for Concave Molds by Conductive Elastic Wheel Containing Carbon Black
Evaluation of the Relationship Among Dressing Conditions Using Prismatic Dresser, Dressing Resistance, and Grinding Characteristics
Microscopic Wear Characteristics of Ceramic Grinding Wheel in Creep Feed Grinding
Special Issue on High Performance Abrasive Technologies
Investigation of the Surface Roughness in Infeed Centerless Grinding of SCM435 Steel
Fault-Tolerant Aircraft Control Based on Self-Constructing Fuzzy Neural Network for Quadcopter
Effect of Ultrafine Bubbles on Pseudomonas Aeruginosa and Staphylococcus Aureus During Sterilization of Machining Fluid
Study on Grinding of Hypocycloid-Curved Rotor Made of Alumina Ceramics with a Small-Diameter Ball-End Electroplated Diamond Grinding Wheel
Measurements of Non-Grinding Forces and Power
Photoelectrochemical Oxidation Assisted Catalyst-Referred Etching for SiC (0001) Surface
Improvement of Removal Rate of Tape Lapping by Applying Fluid with Ultrasonic Excited Cavitation
Evaluation of Grinding Wheel Surface Shape on Difference Multiple Helical Dressing Condition
Development of Resin Fibrous Grinding Wheels Using Twin Nozzle PELID and Analysis of Their Grinding Performance
Development of a Forward-Reverse Rotating cBN Electroplated End Mill Type Tool for Cutting and Grinding CFRP
Investigation on Feasibility of Polishing Concave Surfaces Using Magnetic Compound Fluid Slurry
Effect of Cutting Speed on Shape Recovery of Work Material in Cutting Process of Super-Elastic NiTi Alloy
Investigation on Polishing of Zirconia Ceramics Using Magnetic Compound Fluid: Relationship Between Material Removal and Surface Roughness
Investigation of Optimum Grinding Condition Using cBN Electroplated End-Mill for CFRP Machining
Special Issue on Advances in Abrasive Technology
Utilization of Reluctance Electromagnetic Force of Inner-Mover-Type Rotary-Linear Motor
A Puncturing Device that Mimics the Mechanism of Mosquito’s Proboscis and Labium – Verification of the Effect of Skin Deformation / Needle Buckling Prevention Mechanism and Puncture Experiment on Artificial Skin and Experimental Animals –
Mitigation of Channel Clogging in a Microfluidic Device for Capturing Circulating Tumor Cells
Using Textured-DLC Coating to Improve the Wear Resistance of Stainless Steel Plate Under Dust-Containing Lubricant Condition
Development of a Microprobing System for Side Wall Detection Based on Local Surface Interaction Force Detection
Positioning Performance Evaluation for Light-Weight Rotary Stage CFRP Application
Relationship Between Fluid Properties and Bearing Stiffness in Water Hydrostatic Bearing
Compensation Method for Tool Setting Errors Based on Non-Contact On-Machine Measurement
Grinding Energy Distributions and Wear Behaviors of Grain Cutting Edges in cBN Deep Grinding
Angle Detection Using Gyro Signals Rotating Around Four Orthogonally Aligned Axes
Cutting Features Between Surface Roughness in Feed Direction and Machining State of Radius End Mill Against Inclined Surfaces (In Case of Contour Machining and Five-Axis Machining with Constant Tilt Angle)

*This site is desgined based on HTML5 and CSS3 for modern browsers, e.g. Chrome, Firefox, Safari, Edge, Opera.

Last updated on Mar. 29, 2023